TASCAM Portacapture X6
57
16 - Messages
The following is a list of pop-up messages.
Refer to this list if one of these pop-up messages appears on the Porta-
capture X6 and you want to check the meaning or determine a proper
response.
Message
Details and response
Hold On
Buttons have been disabled by the HOLD
switch.
No Card
Load a microSD card.
Card Error
The microSD card could not be recognized.
Change the microSD card.
Card Full
The microSD card has no remaining capaci-
ty.
Format Error
Format Card
The microSD card might not be formatted
properly, or it might be broken.
Tap the screen to start formatting.
Formatting will erase all data on the mi-
croSD card.
Invalid Card
Change Card
Something might be wrong with the microSD
card.
Change the microSD card.
MBR ERROR
Init CARD
The microSD card might not be formatted
properly, or it might be broken.
Tap the screen to start formatting.
Formatting will erase all data on the mi-
croSD card. If formatting is not possible,
change the microSD card.
Write error
Recording will continue
Writing to the microSD card timed out. This
has caused audio to be interrupted and
noise to occur.
A BOF mark was added at the point when
audio was interrupted.
Card slow
Check BOF mark
microSD card writing performance has be-
come worse.
A BOF mark has been added at the point
when audio was interrupted because writ-
ing to the microSD card timed out.
Check the audio around the BOF mark.
Execute the erase format function or
change the microSD card.
Invalid SysFile
Make Sys File
The system file required to operate this unit
is invalid.
Tap the screen to create a system file.
Non- Supported
See the Reference Manual for file formats
that this unit can use. (page 60)
File Num Full
Recording is not possible because the total
number of folders and files would exceed
the limit of 5000.
File Not Found
The file was not found or might be dam-
aged.
Check the relevant file.
Cannot delete because file
protected
Remove protection from a file before trying
to delete it.
Cannot divide because file
too short
The file is too short, so it cannot be divided.
MP3 files cannot be divid-
ed
MP3 files cannot be divided.
No marks so cannot divide
Files that do not have marks cannot be di-
vided with this function.
Can’t divide
Short interval
Mark division will not work when the inter-
val between marks is two seconds or less.
Can’t divide
No file
There is no audio file.
Message
Details and response
Cannot divide because file
name invalid
Division is not possible because the file
name would exceed the limit of 200 char-
acters.
Use a computer to change the file name.
Can’t delete
Not empty
Folders that contain files cannot be delet-
ed.
Delete all the files in the folder and try
again.
No XRI data
No XRI data has been saved in the file. Turn
the XRI data recording function ON before
starting recording.
XRI data cannot be saved when recording
MP3 files.
Adding marks not possible
because file protected
Marks cannot be added because the file is
protected from writing.
Remove protection from a file to add marks
to it.
Can’t MARK
File length
Marks cannot be added because the file is
too short.
I/O Too Short
The IN and OUT points are too close togeth-
er. Set them with at least 1 second between
them.
Dual format not possible
MP3 dual format recording cannot be used
when the sampling frequency is 96 kHz.
File error
If any of these errors occurs, turn the unit
off and restart it.
If the unit cannot be turned off, remove the
batteries, and disconnect the AC adapter
(TASCAM PS-P520U, sold separately).
If these error messages continue to appear
frequently, please contact a TEAC Repair
Center.
Error occurred
Playback Error
Writing Failed
System error XX
(XX is a number)
USB FS Mismatch
The sampling frequency settings of this
unit and the computer are not the same.
Change the setting of one so that they are
the same.
Already used in another
pad
The same pad data cannot be used for two
sound pads at the same time.
Battery is overheated.
Change to USB power
supply.
The internal temperature has become high-
er when using AA batteries. You can con-
tinue to use the unit by powering it with a
USB connection.
Device is overheated.
Turn off the power.
The internal temperature has become high-
er. The system will shut down automatically.
The USB power supply is
less than 1500 mA.
Use of a function that cannot be used when
power is less than 1500 mA was attempted.
Connect an external power supply that can
provide at least 1500 mA, or set the unit to
operate using battery power and disable
energy-saving mode.
No track selected
No recording track has been selected.
Turn input on for tracks to be recorded on
the Input Screen. (page 28)
