14
TASCAM MZ-372
Operation procedures
After turning the power on, adjust the levels of the
input signals.
Adjusting mic input channels (1-6)
1.
Set the channel 1–6
GAIN
(
4
) and
EQ
(
r
) knobs
to their center values.
2.
Press the channel 1–6
SOURCE SELECT
(
5
)
C/
MIC
switches so the
C/MIC
indicators (
2
) light.
3.
When connecting a mic to a channel 1–6
C
(MONO)
/MIC
(
h
) input jack, set the
INPUT LEV-
EL
switch (
j
) to
MIC
.
4.
Set the
MAIN OUTPUT VOL
(
8
) knob levels low.
5.
Try speaking into the mic.
Use the channel 1–6
GAIN
(
4
) knob to adjust the
input level so that its level meter (
t
) lights around
0 dB
.
6.
Use the channel 1–6
EQ
(
r
) knobs to adjust the
equalizer.
7.
Follow the above procedures for other input
channels with connected mics.
Adjusting line input channels (1-6)
1.
Set the channel 1–6
GAIN
(
4
) and
EQ
(
r
) knobs
to their center values.
2.
When connecting an audio device to channel 1–6,
press the
SOURCE SELECT
switch (
5
), so that the
SOURCE SELECT
indicator (
A
/
B
/
C/MIC
) lights.
3.
When connecting an audio device to a channel
1–6
C (MONO)
/MIC
(
h
) input jack, set the
INPUT
LEVEL
switch (
j
) to
LINE
.
When connecting an audio device to channel 1–6
LINE A
/
B
(
v
) input jacks, set the
LINE/PHONE
switch (
k
) to
LINE
.
4.
Set the
MAIN OUTPUT VOL
(
8
) knob levels low.
5.
Start playback on the connected audio device.
Use the channel 1–6
GAIN
(
4
) knob to adjust the
input level so that its level meter (
t
) lights around
0 dB
.
6.
Use the channel 1–6
EQ
(
r
) knobs to adjust the
equalizer.
7.
Follow the above procedures to adjust other input
channels with connected audio devices.
Adjusting the input of a mic connected
to the MAIN MIC INPUT jack
1.
Connect a mic to the
MAIN MIC INPUT
jack (
w
),
and press the
MAIN MIC
(
2
) switch so the
MAIN
MIC
(
2
) indicator lights.
2.
Use the
MAIN MIC INPUT VOLUME
(
1
) knob to
adjust the mic input level.
3.
Use the
MAIN MIC INPUT EQ
(
e
) knobs to ad-
just the 2-band (HIGH/LOW) equalizer for the mic
sound.
Output channels
Output signals can be sent to the following jacks from
the stereo output bus.
0
MAIN OUTPUTS 1-2 (UNBALANCED)
(
f
) and
MAIN OUTPUTS 1-2 (BALANCED)
(
c
) jacks
0
SUB OUTPUT
(
x
) jacks
0
MONITOR OUT
(
z
) jacks
NOTE
The output level from the
MONITOR OUT
(
z
) jacks
cannot be adjusted.
Adjusting the levels output from the MAIN
OUTPUTS 1-2 (UNBALANCED) and MAIN
OUTPUTS 1-2 (BALANCED) jacks
While checking the output level indicators (
7
), use
the channel faders (
6
) and
MAIN OUTPUT VOL
(
8
)
knobs to adjust the output levels. The optimal output
level adjustment is usually when the output level indi-
cators (
7
) light around 0 dB.
When an amplifier is connected to the
MAIN OUT-
PUTS 1-2 (UNBALANCED)
(
f
) or
MAIN OUTPUTS
1-2 (BALANCED)
(
c
) jacks, set the
ATTENUATOR
(
g
)
switch to
OFF
if it accepts high gain or
ON (-6dB)
if it
accepts low gain.
Adjusting the level output from the SUB
OUTPUT jacks
Use the
SUB OUTPUT VOL
(
q
) knob to adjust the out-
put level.
If the
MONO
(
0
) switch is set to ON (
MONO
indicator
lit) mono signals will be output from all output jacks.
To output mono signals from only the
SUB OUTPUT
(
x
) jacks, set the
SUB OUTPUT
(
d
) switch to
MONO
.
