background image

 

 

 

TASCAM CD-A750 RS-232C Protocol Specifications 

                                                                                                                                                                                               
 

3

 TEAC 

Corporation

 

1.

 

Overview 

 
The CD-A750 can be controlled by computer or external device via RS-232C connector on the rear panel 
with the RS-232C serial protocol. In this document, the CD-A750 is referred to as the "controlled device," 
and the external device that controls it is referred to as the "external controller." 

 
2.

 

Specifications 

 
Electrical specifications 

Conforms to standard 

JIS X-5101

 

(equivalent to former JIS C-6361 and EIA RS-232C) 

 

(Not compatible with the RS-422A used in professional VTR units) 

Impedance at receiver 

Measured with an applied voltage of between ±3 and 15V, the DC 
resistance is between 3K

 and 7K

 

Total load capacitance is less than 2500pF 

Open circuit voltage at transmitter  Less than 25V 
Open circuit voltage at receiver 

Less than 2V 

Signal voltage 

Open circuit voltage at the receiver is 0V, the signal voltage is 
between ±5V and ±15V for a load impedance of between 3K and 
7K

Signal discrimination 

Logical “1” 

Less than -3V 

 

Logical “0” 

More than +3V 

 

Communication format 

Circuit type 

3-wire, half-duplex 

Transmission type 

Digital binary serial 

Data speed (baud rate) 

4800/9600/19200/38400 bit/sec 

Character length 

7/8 bit 

Parity bit 

Odd/Even/None 

Stop bit 

1/2 bit 

(Data speed, character length, parity bit, and stop bit settings are made on the controlled device.) 

 

Connector pin-out 

Connector 

D-sub 9-pin female (unified screw thread) 

 

 

Terminal pin-out and input/output signals 

Pin no. 

In/Out 

Signal name 

Description 

1 - 

NC 

Not 

connected 

In 

Rx Data 

Data received at this pin *1 

Out 

Tx Data 

Data transmitted from this pin 

4 Out 

(Reserved) Reserved 

5 - 

GND 

Ground 

6 In 

(Reserved) 

Reserved 

Out 

RTS 

Request To Send (output "request to transmit") *2 

In 

CTS 

Clear To Send (input "ready to receive") *2 

9 - 

NC 

Not 

connected 

*1

  A voltage that satisfies the RS-232C specification must be applied to Rx Data. 

*2

  RTS/CTS is loopback-connected within the controlled device. If using RTS/CTS control, consider the 

design of the external controller. 
 

Summary of Contents for CD-A750




























Reviews: