Tascam CD-01U Professional Specifications Download Page 20

Page: 20 / 26

TASCAM CD-01U/CD-01U PRO RS-232C Protocol Specifications

TEAC Corporation

5-8. TIMER/RESUME PLAY SELECT RETURN

Transmitted in response to a TIMER/RESUME PLAY SELECT command [34] with the request data
([FF]) to show the currently set the Power-on-play/Resume function status .

Command

Data

2 bytes

Request command TIMER/RESUME PLAY SELECT [34]

Data 1

Data 2

Description

Remarks

Timer Off/Resume Off

Timer On/Resume Off

Timer Off/Resume On

Timer On/Resume On

5-9. PITCH CONTROL SELECT RETURN

Transmitted in response to a PITCH CONTROL SELECT command [35] with the request data ([FF]) to
show the currently set the Pitch Control mode status .

Command

Data

2 bytes

Request command PITCH CONTROL SELECT [35]

Data 1

Data 2

Description

Remarks

Pitch Control Off

Pitch Control mode is turned off

Pitch Control On

Pitch Control mode is turned on

5-10. AUTO READY SELECT RETURN

Transmitted in response to an AUTO READY SELECT command [36] with the request data ([FF]) to
show the currently set the Auto Ready mode status .

Command

Data

2 bytes

Request command AUTO READY SELECT [36]

Data 1

Data 2

Description

Remarks

Auto Ready Off

Auto Ready function is turned off

Auto Ready On

Auto Ready function is turned on

5-11. REPEAT SELECT RETURN

Transmitted in response to a REPEAT SELECT command [37] with the request data ([FF]) to show the
currently set the repeat function status .

Command

Data

2 bytes

Request command REPEAT SELECT [37]

Data 1

Data 2

Description

Remarks

Repeat Off

Repeat mode is off

Repeat On

Repeat mode is on

Summary of Contents for CD-01U Professional



























Search results

Summary of Contents for CD-01U Professional

Reviews:

Related manuals for CD-01U Professional

Brands by name

Popular brands

Tascam CD-01U Professional, Specifications

Search results

Summary of Contents for CD-01U Professional

Reviews:

Related manuals for CD-01U Professional

Brands by name

Popular brands