background image

 

2

 

 

 

TASCAM 302MKII

 

Important Safety Precautions

 

DO NOT cut off the mains plug from this equipment.

 

If the plug fitted is not suitable for the power points in your home or
the cable is too short to reach a power point, then obtain an
appropriate safety approved extension lead or consult your dealer.

If nonetheless the mains plug is cut off, remove the fuse and dispose
of the plug immediately, to avoid a possible shock hazard by
inadvertent connection to the mains supply.

If this product is not provided with a mains plug, or one has to be
fitted, then follow the instructions given below:

 

IMPORTANT:

 

 

 

DO NOT

 

 make any connection to the larger

terminal which is marked with the letter E or by the safety earth
symbol 

 

ç

 

 or coloured GREEN or GREEN-and-YELLOW.

The wires in the mains lead on this product are coloured in
accordance with the following code:

 

BLUE :

 

NEUTRAL

 

BROWN :

 

LIVE

 

As these colours may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.

When replacing the fuse only a correctly rated approved type should
be used and be sure to re-fit the fuse cover.

IF IN DOUBT — CONSULT A COMPETENT ELECTRICIAN.

 

IMPORTANT (for U.K. Customers)

 

TO THE USER
This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reason-
able protection against harmful interference
when the equipment is operated in a commer-
cial environment. This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance with
the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residental area
is likely to cause harmful interference in which
case the user will be required to correct the
interference at his own expense.

 

CAUTION

 

Changes or modifications to this equipment not
expressly approved by TEAC CORPORATION
for compliance could void the user’s authority to
operate this equipment.

 

For U.S.A

 

AC POWER CORD CONNECTION

CAUTION:

 

TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.

 

CORDE DE CONNEXION CA

ATTENTION:

 

POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE
L A   F I C H E   D A N S   L A   B O R N E
C O R R E S P O N D A N T E   D E   L A   P R I S E   E T
POUSSER JUSQU’AU FOND.

 

For CANADA

Summary of Contents for 302mkII





















Reviews: