Target PRO 35 III DIESEL, Operating Instructions Manual

Page: 25 / 46

25
(See Fig. 1, 2, and 3)
Turn engine off. Set Speed Control Lever
(1S) to STOP position. Remove diamond
blade (2E) before transport. Set Neutral
Control Knob (1W) to ENGAGE position
(DOWN). Set Parking Brake (1N) ON (UP)
(if equipped).
When moving the saw up and down ramps, with the
engine on,
use extreme caution .
•
To go DOWN a ramp, drive the saw FORWARD slowly.
•
To go UP a ramp, back the saw in REVERSE slowly.
WARNING! DO NOT roll the saw down a
ramp while the transmission is in
NEUTRAL (1V).
Lifting The Saw. The saw can only be lifted by
the factory installed Lifting Bail (3B).
To Transport By Vehicle:
•
Set Engine Start Switch (1L) in the “0” (OFF) position.
•
Set Speed Control Lever (1S) in the STOP (1V) position.
•
Set Transmission Engage (1W) to engage down
position.
•
Set Parking Brake (1N) to up position (if equipped).
•
Push Handle Bars (1B) inward and tighten Knobs (1A).
Block the saw in place and secure it into
place with chains or straps to prevent
movement during transport.
4 CHECK BEFORE STARTING
Take into account the working conditions from
the health and safety point of view.
•
Fuel: Check the engine maintenance manual.
∗
Diesel Models: #2 Diesel fuel is recommended.
•
Check that the engine oil level is correct. Because the
engine often operates at an angle, check the oil level
(with engine horizontal) frequently to ensure that the
oil level never falls below the lower mark on the
dipstick. 15W40 oil is recommended.
•
For start up, refer to the engine manual.
5 FITTING THE BLADE
(See Fig. 1 and 2)
Always set the Engine Start Switch (1L) to
the “0” (OFF) position before mounting the
blade.
•
Set the Engine Start Switch (1L) to the “0” (OFF)
position.
•
Raise the machine to a high position [by pressing the
Toggle Switch (1R) on the Control Lever (1S) upward].
•
Loosen the bolt on the Blade Guard Latch (2G).
•
Raise the front half of the Blade Guard (2H).
•
Unscrew the Blade Shaft Bolt (2A) or Nut (2A). Re-
move Outer Flange (2B).
•
Fit Diamond Blade (2E) to Outer Flange Arbor (2C) or
Shaft Arbor (2I).
•
Install Outer Flange (2B) into the Blade Shaft (2I) mak-
ing sure that the Locking Pin (2D) passes through the
Diamond Blade (2E) and into the Inner Flange (2F).
Note the direction of rotation of the blade.
The direction of rotation is shown by an
arrow on both the Diamond Blade (2E) and
the Blade Guard (2H). Make sure that the
contact surfaces on the Diamond Blade (2E),
Inner & Outer Flanges (2B & 2F) and Blade
Arbor (2C) are clean.
•
Rotate Outer Flange (2B) and Diamond Blade (2E) in
the opposite direction of blade rotation to remove
backlash.
•
Install and tighten Blade Shaft Bolt (2A) or Nut (2A)
using the Blade Shaft Wrench while firmly holding the
Diamond Blade (2E).
•
Lower front half of Blade Guard (2H) and tighten the
Bolt (2G) on the Blade Guard Latch (2G).
The Blade Shaft Bolt (2A) or Nut (2A) on the
Right Hand side has Left Hand threads. The
Blade Shaft Bolt (2A) or Nut (2A) on the Left
Hand side has Right Hand threads.
Slip on blade guards are provided with a safety
latch which engages the support spade and a
bolt to retain the rear of the guard.
Do not operate this saw without the latch
engaged and the bolt installed. Inspect blade
guards and latches frequently. DO NOT USE
IF DAMAGED.
3 TRANSPORT (BLADE REMOVED)