Taramps HOMEE TPS 6000 Instruction Manual Download Page 8

Rear Panel

5 - FM ANTENNA: 

Indoor wire antenna for FM radio reception. Position the wire antenna in 

order to achieve the best FM reception.

3  -  OUT:

  The  LINE  OUT  output  allows  to  send  the  audio  signal  (not  amplified)  to  other 

equipment, such as another  THS 6000, an amplifier or active subwoofer.

The LINE OUT sound is affected by the 3 Band Equalizer and Volume controls. (LOW, MID, HIGH 

and VOLUME controllers).

Using the OPTICA input, you have the AUTO TURN ON/OFF system, which automatically turns 

the device on/off when there is an optical signal at the input. This function can be disabled 
according to the configuration instructions on page 05.

To  use  these  inputs,  the  device  must  be  in  the  AUX  or  DIRECT  AUX  function.  Use  the 

AUX1/AUX2 front button to select the desired input. OPTICAL input is automatically selected 
when an optical signal is present, regardless of the position of the front panel AUX1/AUX2 key.

4 - INPUT AUX 1, OPTICAL e AUX 2:

 Audio inputs.

IMPORTANT:

  for  the  optical  signal  to  work  correctly,  the  TV  or  signal  source  must  be 

configured as standard PCM output. Strong noises indicate that the received signal is not PCM 
standard. In this case, check the TV menu to see if the digital audio output format is PCM. 
(Consult your TV manufacturer's manual).

2  -  SPEAKER  OUT:

  Power  output  for  connecting  speakers.  In  this  case,  there  are  two 

connection  possibilities:  the  normal  one  with  a  box  at  each  output  and  the  BRIDGED 
connection that joins two channels into one, for greater power. Follow the indicated polarity 
and the recommended minimum impedance of 2 Ohms for normal connection and 4 Ohms 
for Bridged connection.

1 - POWER CABLE

: Plugged it into a powered outlet. . This product operates from 127V AC 

to220V AC.

Knowing your equipment

Protection System

The THS 6000 has a protection system against outputs overload and outputs short circuit.
When the protections are activated, the ATT LED on the front panel turns on temporarily and the 
audio output is interrupted. About 2 seconds, or the audio is restored.
If the protection system or system meets frequently, review the settings and installation of your 
system.

07

Summary of Contents for HOMEE TPS 6000
















Reviews: