background image

 

6

 

BWC

-

040, BWC

-

040EC, BWC

-

060 Wood Chipper

 

Important Safety Information

 

 

Safety

 

 

It is important that you read the entire manual and to become familiar with this product before you begin using 
it. This product is designed for certain applications only. The manufacturer cannot be responsible for issues 
arising from modification. We strongly recommend this product not be modified and /or used for any applica-
tion other than that for which it is designed. If you have any questions relative to a particular application, DO 
NOT use the product until you have first contacted us to determine if it can or should be performed on the 
product.

 

 

Read and understand this manual and all safety signs before operating and maintaining . Review the safety in-
structions and precautions annually.

   

 

 

 

Safety Signal Words

 

 

TAKE NOTE! This safety alert symbol found though out this manual is used to call you attention to in-

structions involving you personal safety and the safety of others. Failure to follow these instructions can 

result in injury or death.

 

 
 
 

 
 
 
 
 
 

 

This symbol means:

 

Attention!

 

Become alert!

 

Your safety is involved!

 

 

Note the use of the signal words, DANGER, WARNING and CAUTION with the safety messages. 
The appropriate signal word for each has been selected using the following guidelines:

 

 

DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or 
serious injury. This signal word is to be limited to the most extreme situations typically for machine 
components which, for functional purposes, cannot be guarded.

 

 

WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or 
serious injury, and includes hazards that are exposed when guards are removed. It may also be used 
to alert against unsafe practices.

 

 

CAUTION: Indicates a potentially hazardous situation that, if not avoided, may result in minor or 
moderate injury. It may also be used to alert against unsafe practices.

 

Summary of Contents for BWC-040EC





































Reviews: