Tao Motor BULL 150 Owner'S Manual Download Page 20 | Manualshive

Page: 20 / 80

background image

1. Seat Lock Lever

2. Frame 3. Seat Tab

SEAT

To Remove Seat

To remove the seat, pull the seat lock lever

(#1) backward and then pull up the seat. The seat lock is located under the seat in

the back of the ATV.

To Install Seat

Insert tab

(#3) on the front of the seat into the seat holder

(#2) and push down on the seat at the rear. Make sure that the seat is

securely installed in place and will not move during operation.

11

«
...
18
19
20
21
22
...
»

Summary of Contents for BULL 150

















































































Reviews:

No comments

Related manuals for BULL 150

Brand: KYMCO Pages: 1

2007 Outlander 500 EFI

Brand: Can-Am Pages: 148

Brand: Lynx Pages: 196

Brand: Kärcher Pages: 16

MIC 45 advanced

Brand: Kärcher Pages: 19

Brand: Variant Pages: 16

1988 Citation LS

Brand: BOMBARDIER Pages: 52

Brand: BOMBARDIER Pages: 80

1995 TRX 400 FW

Brand: Honda Pages: 155

Brand: Yamaha Pages: 180

Brand: Honda Pages: 5

BIGFOOT B5-440-36

Brand: Taylor-Dunn Pages: 130

Brand: Yamaha Pages: 1664

Commander 1000 Can-Am 2013

Brand: BRP Pages: 16

Brand: Toro Pages: 44

Quad Raider 600

Brand: Sym Pages: 247

Brand: Opus Pages: 25

Brand: Opus Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands