Tao Motor BULL 150 Owner'S Manual Download Page 65

Page: 65 / 80

To tighten drive chain,

1. Loosen the chain adjuster nut(#1) on the back side of the carrier/housing.

2. Tighten the chain adjuster nuts(#2) to move the carrier/housing forward.

3. When proper chain slack is achieved tighten chain adjuster nuts (#1,3).

To loosen drive chain,

Loosen the chain adjuster nut (#1) on the back side of the carrier/housing.

Loosen the chain adjuster nuts (#2,3).

Tighten the chain adjuster nuts (#1) on the back side of the carrier/housing . To move the carrier/housing rearward.

When proper chain slack is achieved tighten chain adjuster nuts (#2,3).

Drive chain slack:

6.0-12.0 mm (0.24-0.47 in)

Tightening Torques:

14 Nm / 10 ft/lbs Chain Adjuster Nuts (#1,2,3)

45 Nm / 33 ft/lbs Carrier/Housing Bolts

1. Remove all dirt and mud from the drive chain with a brush or cloth.

2. Spray chain lubricant on the entire chain, making sure that all side plates and rollers have been sufficiently oiled.

NOTICE

The drive chain must be lubricated after washing the ATV or riding in the rain or wet areas.

Tighten carrier housing bolts.

Cleaning Lubricating Drive Chain

The drive chain must be cleaned and lubricated at the intervals specified in the periodic maintenance and lubncat1on chart, otherwise it will

quickly wear out, especially when riding in dusty or wet areas.

Service the drive chain as follows.

Summary of Contents for BULL 150

















































































Search results

Summary of Contents for BULL 150

Reviews:

Related manuals for BULL 150

Brands by name

Popular brands

Tao Motor BULL 150, Owner'S Manual

Search results

Summary of Contents for BULL 150

Reviews:

Related manuals for BULL 150

Brands by name

Popular brands