background image

MAIN BURNER 
(#48) ORIFICE  (5021.3407)

MINIMUM RATE SCREW (5005.011)

CONVERSION LABEL (5052.52085)

 For use with model:
 Pour utilise avec du modèle:

LP GAS/ 

DU GAZ LP 

12.5 in/wc /12.5 po/c.e. 
     (3.11 kPa) 

      

13.9 in/wc / 13.9 po/c.e. 
     (3.45 kPa) 

      

11.0 in/wc / 11.0 po/c.e. 
     (.95 kPa) 

      

# 48     (1.93 mm) 

Max.:   35,000   (10.3)
Min.:    27,000  (7.91)

 

080411 6-TC30 5052.52085

Date:

 ______________________

By / Par:

 ___________________  

This appliance was converted 
to PROPANE GAS with this kit 
on this date by the organiza-
tion which accepts the respon-
sibility that this conversion 
has been properly made. / Cet 
appariel etair converter au gaz 
LP par l’emploi de la trousse 
de conversion par une organi-
zation qui accepte la responsi-
bilité pour une installation en 
bon état.

 

TC30

Series C

If the unit is to be used on propane 
convert as follows using the 
components supplied with this 
burner:

CAUTION

The gas supply and electrical power 
shall be shut off before proceeding 
with the conversion.

Note: Factory supplied components must be 
used to ensure correct input.  
After conversion confi rm proper manifold 
pressure.

1. 

Ensure the burner, pilot and gas 

 

supply are turned off, and the 

 

appliance has cooled.

2. 

Remove the two screws securing the  

 

the burner grate. 

 (Fig. 

#14)

3.  

Remove the two screws securing the 
manifold assembly to the burner. 

 (Fig. 

#15)

4.  

Remove the manifold assembly from the 
burner. (Fig. #16)

WARNING

This conversion kit 
shall be installed by a 
qualifi ed service agency 
in accordance with the 
manufacturer's instructions 
and all applicable codes 
and requirements of 
the authority having 
jurisdiction. 

If the information in these 
instructions is not followed 
exactly, a fi re, explosion 
or production of carbon 
monoxide may result 
causing property damage, 
personal injury or loss of 
life. 

The qualifi ed service 
agency is responsible for 
the proper installation of 
this kit. 

The installation is not 
proper and complete 
until the operation of the 
converted appliance is 
checked as specifi ed in the 
manufacturer's instructions 
supplied with the kit.

Fig #14

Fig #15

Fig #16

9

TC30.NG06C 200411-16

Propane Conversion

Summary of Contents for TC30

















Reviews: