background image

135

D14049.04 
JULY 2008

Grey Headline 

(continued)

TANDBERG

 VIDEO COMMUNICATIONS SERVER 

ADMINISTRATOR GUIDE

Introduction

Getting Started

Overview and 

Status

System 

Configuration

VCS  

Configuration

Zones and 

Neighbors

Call  

Processing

Bandwidth 

Control

Firewall 

Traversal

Appendices

Applications

Maintenance

Bandwidth Control Overview

The diagram below shows a typical network deployment: 

a broadband LAN between the Enterprise and the internet, where high bandwidth calls are acceptable

• 

a pipe to the internet (Pipe A) with restricted bandwidth

• 

two satellite offices, Branch and Home, each with their own internet connections and restricted pipes. 

• 

In this example we have created new subzone for each pool of endpoints, so that we can apply suitable limitations to the bandwidth used within and 
between each subzone based on the amount of bandwidth they have available via their internet connections. 

The TANDBERG VCS allows you to control 
the amount of bandwidth used by endpoints 
on your network. This is done by grouping 
endpoints into subzones, and then applying 
limits to the bandwidth that can be used:

within each subzone

• 

between a subzone and another subzone

• 

between a subzone and a zone. 

• 

Bandwidth limits may be set on a call-by-call 
basis and/or on a total concurrent usage basis.  
This flexibility allows you to set appropriate 
bandwidth controls on individual components 
of your network. 
This section describes the different types of 
subzones and how to add and configure them, 
and explains how to use 

Links

 and 

Pipes

 to 

apply bandwidth controls between subzones 
and zones.

HEAD OFFICE

VCS CONTROL

HOME OFFICE

BRANCH OFFICE

Branch Office

Subzone

Default

Subzone

Pipe A

Pipe B

Pipe C

Home Office

Subzone

INTERNET

Bandwidth Control on the VCS

Example Network Deployment

!

Calls will fail if links are not 
configured correctly.  You can check 
whether a call will succeed, and what 

bandwidth will be allocated to it, using the 
command 

xCommand CheckBandwidth

.

For specific information about how 
bandwidth is managed across Peers in 
a cluster, refer to the section 

Sharing 

Bandwidth Across Peers

.

Summary of Contents for VCS





















































































































































































































































































Reviews: