background image

                                                                                                       TX7322 Addressable Sounder Base 

 

 

        Installation & Operation Manual  

04 

84.1 

970Hz 1s off / 1s on 

05 

82.3 

970Hz, 0.5s / 630Hz, 0.5s 

06 

86.2 

500Hz - 1200Hz×3, 3.5s on / 0.5s off 

07 

87.4 

2850Hz, 0.5s on / 0.5s off×3 / 1.5s off 

08 

87.4 

2850Hz 0.4s on, 0.3s off 

09 

83.2 

550Hz, 0.7s / 1000Hz, 0.33s 

10 

10 

84.3 

1500Hz -2700Hz @ 3Hz 

11 

11 

80.5 

2400Hz 

12 

12 

83.5 

500Hz -1200Hz @ 0.33Hz 

13 

13 

84.6 

2400Hz -2900Hz @ 9Hz 

14 

14 

87.8 

2400Hz -2900Hz @ 3Hz [Default] 

15 

15 

85.6 

800Hz-970Hz @ 3Hz 

16 

16 

86.5 

500Hz-1200Hz, 3.75s / 0.25s off 

17 

17 

78.9 

800Hz 1s off / 1s on [Pre-alarm] 

 

1.

 

Attach  the programming tool  to 1 and 6 Terminals of Addressable Sounder Base. Press 

“Power” to switch-on the unit.  

2.

 

Switch-on the programmer, then press button “4” to set the desired tone, as shown in figure 

14.  Write the number of the corresponding tone  and  click the button “write”.  The word 

“Success”  or  “Fail”  on the screen  means that the success  or not of the encoding mode 

setting, as shown in figure 15 and figure 16. 

3.

 

Press “Exit” key to go back Main Menu. Press “Power” to switch off the programmer.  

Address:014

Tone:014

Success

Fail

Tone:014

 

                                                                                                                               4050100446-Rev1.0-0917                                                                      

 

 

    TANDA UK  

                                                                                                                                           

Specifications are subject to change without prior notice 

      

 

Summary of Contents for TX7322













Reviews: