background image

 

 

 

www.tanaka-usa.com

                                                   1                                             

 [email protected] 

Owner’s Manual 

TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF

 

 

 

 

 

 

Before using this unit: 

• 

Read the operator’s manual carefully. 

• 

Check that the cutting equipment is correctly assembled  

and adjusted. 

• 

Start the unit and check the carburetor adjustment.   

See “Maintenance”.

 

 

 

 

  

 

          

 

 

 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

 

 

 
 

 
 
 
 

 

 

 
 

 
 

 

WARNING 

Read, understand and follow all 
warnings and instructions in this 

manual and on the unit. 

Always wear eye, head and ear 

protectors when using this unit. 

It is important that you read, fully understand and
observe the following safety precautions and
warnings. Careless or improper use of the unit
may cause serious or fatal injury. 

The engine exhaust from this product 

contains chemicals known to the State 

of California to cause cancer, birth 

defects and other reproductive harm.

 

Keep all children, bystanders and helpers 15m 
(50ft.) away from the unit.  If anyone 

approaches you, stop the engine and cutting 

attachment immediately. 

Summary of Contents for TPE-2501













Reviews: