background image

 

 

 

www.tanaka-usa.com

                           

 

    10                                           

 [email protected] 

Owner’s Manual 

TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF

 

 

Maintenance schedule 

Below you will find some general maintenance instructions. 

For further information please contact your service dealer. 

 

Daily maintenance 

• 

Clean the exterior of the unit. 

• 

Check the blade guard for damage or cracks. Change the guard in case of impacts or cracks. 

• 

Check that the cutting attachment is properly centered, sharp, and without cracks.  As off-centered 
cutting attachment induces heavy vibrations that may damage the unit. 

• 

Check that the cutting attachment nut is sufficiently tightened. 

• 

Check that nuts and screws are sufficiently tightened. 

 

Weekly maintenance 

• 

Check the starter, especially cord and return spring. 

• 

Clean the exterior of the spark plug. 

• 

Remove it and check the electrode gap. Adjust it to 0.6 mm, or change the spark plug. 

• 

Clean the cooling fins on the cylinder and make sure the air intake at the starter is not clogged. 

• 

Check that the angle gear is filled with grease up to ¾. 

• 

Clean the air filter. 

 

Monthly maintenance 

• 

Rinse the fuel tank with gasoline. 

• 

Clean the exterior of the carburetor and the space around it.  

• 

Clean the fan and the space around it.

 

 

 

 

 

Summary of Contents for TPE-2501













Reviews: