background image

 

 

Talius Habitat Screen

TM

 Installation Guide 

Version 2018.1

©TALIUS 

 
SECTION FIVE: MOUNTING RAILS AND PANEL BOX

 

In this section the framework will be attached to the opening. 

Note for this section the panel box will 

need to be fitted into the rails when it’s li

fted into place. 

 

5.1)

 Slide the panel box endplate legs into the guide rails. As you do this, insert the zippered edges of the curtain 

into the retention insert  
 

 

 

5.2)

 Lift the unit into place being careful to support both the panel box and guide rails to ensure you do not 

break the leg of the end plate. Position and hold the unit over the opening where you wish it to be located. 

Install the top screw in one of the guide rails. Using a 4’ level and ensuring the 

bubble is perfectly centered 

between the lines, level the box and shaft and install the screw into the top hole of the opposite guide rail. Again, 
using the level to ensure the rail is plumb, install a screw first in the bottom of one guide rail before installing 
the remainder of screws in this guide rail. Before continuing to install the second rail, measure to ensure that 
the width of the opening between the rails is the same distance at the top, middle, and bottom of the rails. In 
the case of between jamb installations, you may have to shim the guide rails to get them plumb and parallel from 
top to bottom.  
 

 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 

Summary of Contents for Habitat Screen


















Reviews: