background image

- PB-IN-  50HFA                                    1,650' (   500 m)
- PB-IN-100HFA                                    3,300' (1,000 m)
- PB-IN-200HFA                                    6,600' (2,000 m)

Sound alarm with LED 
- When an audible signal is desired in combination 

with the memory LED, turn the alignment sound 
switch to ON. 

When the alarm memory function is not used, 
leave the receiver terminal 11 unconnected. 
(Logic switch can be in either position.) 

Estimated battery life 

No. of pair 

Md AA 

0.5Ah 

Gel Cell 

1.0Ah 

Gel Cell 

5.0Ah 

8 hr 

16 hr 

83 hr 

2 - 

hr 

41 

hr 

4 - 

20 

hr 

8 - 

10 

hr 

No. of pair 

Md AA 

0.5Ah 

Gel Cell 

1.0Ah 

Gel Cell 

5.0Ah 

7 hr 

14 hr 

71 hr 

2 - 

hr 

35 

hr 

4 - 

17 

hr 

8 - 

hr 

No. of pair 

Md AA 

0.5Ah 

Gel Cell 

1.0Ah 

Gel Cell 

5.0Ah 

5 hr 

11 hr 

58 hr 

2 - 

hr 

29 

hr 

4 - 

14 

hr 

8 - 

hr 

 Unit should be connected to a listed class 2 power 

source capable of providing standby power for at 
minimum 4 hours. 

Troubleshooting 

Operation LED does not light up 

1. Disruption of power or inadequate power.

- Correct power supply.

2. Bad wiring connections or broken wire, short-circuit. 

- Check and correct wiring.

Receiver Alarm LED does not light up when the beam 
is interrupted. 

1. Disruption of power or inadequate power.

- Correct power supply.

2. Bad wiring connections or broken wire, short- 

circuit.

- Check and correct wiring. 

4. Four beams are not interrupted simultaneously.

- Ensure all beams are interrupted at same time.

5. Beam interruption time is shorter than response

time. 

- Adjust response time. 

Receiver Alarm LED stays on 

1. Alignment is out.

- Check and adjust.

2. Obstruction between transmitter and receiver.

- Check site / remove any possible obstacles.

3. Optical parts of units are soiled.

- Clean the optical parts with a soft cloth.

4. Frequency channel setting on transmitter does not

match with that on receiver.

- Readjust to the same channel.

Intermittent alarm 

1. Bad wiring connection.

- Check again.

2. Change of supply voltage.

- Stabilize supply voltage.

3. Obstructing object between transmitter and

receiver.

- Remove the obstruction.

4. Transient spikes on supply cables.

- Relocate.

5. Loose installation of transmitter and receiver.

- Tighten.

6. Optical parts of units are soiled.

- Clean the optical parts with a soft cloth.

7. Poor alignment.

- Check and adjust again.

8. Animals pass through the four beams. 

- Change environment of the installation.

9. Beam power switch is set to L; not enough

sensitivity.

- Set beam power switch to H and make the unit 

gain-locked with the receiver cover detached. 

Specifications 

Detection system 

Near infrared beam 

interruption system 

Infrared beam 

Double modulation pulsed 

beam by LED 

Protection distance 
- PB-IN-  50HFA outdoor

          

165' (  50 m)

..................................
..................................
..................................

...........................

...........................

...........................

 

 

- PB-IN-100HFA outdoor                             330' (100 m)

 

 

- PB-IN-200HFA outdoor                             660' (200 m)

 

 

Max. beam range 

 
 
 

Response time ................................. 0.05sec. to 0.7sec. 

Supply voltage .................. 12V to 30VDC (non-polarity) 

Current consumption 
- PB-IN-  50HFA ...................................................  95mA 
- PB-IN-100HFA .................................................. 105mA 
- PB-IN-200HFA .................................................. 120mA 
Alarm output ....................................... Dry  contact  relay: 
 ..................................................... NC or NO switchover 
 .............................. Reset: Interruption time (Min 2sec.) 
 ............................................. Contact: 30V (AC/DC), 1A 

Environmental ouput   .........................Dry contact 

 ................................................... NC or NO switchover 

 ...... Contact operation: Output when weather condition 

 .......................................gets  worse 

Tamper  output   ...................................... Dry  contact  NC 
 ................................Contact operation:    Output when 
 ............................................. receiver cover is detached 
 .......................................... Contact: 30V (AC/DC), 0.1A 

Alarm LED ...................Red LED (Receiver) lights when 
 ........................................................ an alarm is initiated 

Attenuation LED ..........Red LED (Receiver) lights when 
 ........................................ beam receiption is attenuated 

Functions ............ Modulated beam frequency selection 
 .............................................................. Sound indicator 
 ................................................... Environmental module 
 ............................................... Alarm memory indication 
 .........................................................

.............................................................

..................................................

 Programmed AGC 

 ...................................................Auto-gain lock function 
 .................................................................... Monitor jack 
Ambient temperature range .................

Mounting position .............................................. Outdoor 
Wiring .............................................................  Terminals 
Weight 
- Transmitter ..............................................
- Receiver ...............................................
Appearance ............................... PC  resin  (ruby-colored) 

 .......................................... Contact: 30V (AC/DC), 0.5A 

PB-IN-50HFA

PB-IN-100HFA

PB-IN-200HFA

3. Beam reflection is flooding receiver.
 -   Remove the reflecting object. Contact TAKEX for 

further remedies.

Approvals

CE: conform
National approval conditions relating to the use of the 
product must be followed.

-31ºF to +151ºF 
(-35ºC to +66ºC)

Ingress protection                                                    IP55

42 oz (1.2 kg)

45.5 oz (1.3 kg)

Details for ordering

PB-IN- 50HFA Photoelectric beam sensor (  50 m)
PB-IN-100HFA Photoelectric beam sensor (100 m)
PB-IN-200HFA Photoelectric beam sensor (200 m)

BP-200F Pole cover (2 pcs./set)
HTF-24 Heater (2 pcs./set) 24 V DC: 860 mA

Limited warranty

TAKEX products are warranted to be free from defects 
in material and workmanship for 12 months from 
original date of shipment. Our warranty does not cover 
damage or failure caused by Acts of God, abuse, 
misuse, abnormal usage, faulty installation, improper 
maintenance or any repairs other than those provided 
by TAKEX. All implied warranties with respect to TAKEX, 
including implied warranties for merchantability and 
implied warranties for fitness, are limited in duration  
to 12 months from original date of shipment. During 
the Warranty Period, TAKEX will repair or replace, 
at its sole option, free of charge, any defective parts 
returned prepaid. Please provide the model number 
of the products, original date of shipment and nature 
of difficulty being experienced. There will be charges 
rendered for product repairs made after our Warranty 
Period has expired.

Summary of Contents for PB-IN-100HFA

























Reviews: