Mode selector
1 2 3 4
Detection Sensitivity
Alarm Sound
Detection timer
1
(Factory set : ON)
Detection Sensitivity
SET
L (50%)
SET
H (100%)
(Factory set : H)
2
SET
Timer
(Factory set : 1 sec.)
An alarm output occurs when the flame continues for set time of
detection timer or longer.
Detection timer
3 4
This product alarms only by detecting a flame
continuing for the set time of detection timer.
(1sec., 6secs., 15secs., 30secs.)
When the flame continues further, the alarm and
external output (when wired) are also continued
10sec. after the flame goes out, the alarm stops and
the sensor goes back to armed mode.
Installation hole
approx. 5mm
Marking
Installation hole
Alarm (Basic action)
This product is equipped with installation holes (pitch 3.29" or 83.5mm) to make
installation easy and the sensor's direction adjustable.
Buzzer : Sounds intermittently every 0.2sec.
LED : Flashing every 0.2sec.
〔
〔
Low battery alarm will be initiated when power is
supplied from a battery.
When low battery alarm sounds, change the battery for
new one. (The sensor stops its operation 2 weeks after
the low battery alarm starts.)
Within 30sec. after the power is turned off, power on
notice is not issued even if the power is supplied
again.
Low battery alarm
Buzzer : Sounds intermittently every 5sec.
LED : Flashing every 5sec.
〔
〔
〔
〔
Power on notice will sound when the power is turned on.
When voltage is low, power on notice will not be
heard. Check the power supply (battery).
Power on notice
(1) Operation
When detection sensitivity is set "L", the detection distance is
50% shorter than when it is set "H".
When operation is unstable on "H" setting, select "L".
For semi-outdoor installation, "L" setting is recommended.
[Installation of base]
Check operation and area.
(Ref : Operation check)
When sensor unit is detached,
wrap it in palm and slide
release lever.
To lock sensor unit, insert
sensor locking screw into
locking screw hole and
tighten it.
Set alarming sound, detection
sensitivity and detection timer.
(Ref : 6-(2) Function setting)
Attach the sensor unit to base
unit.
Turn front marks of base
unit and sensor unit to point
in the same direction.
Insert sensor unit into base
unit.
Push sensor unit until
release lever is locked.
Sensor locking screw
×
×
6
OPERATION AND FUNCTION
Place the base on the site and
mark
×
on 2 points 180
°
apart.
Insert the 2 pcs. of tapping
screws (accessory) leaving 5mm
exposed from the surface.
Adjust the sensor's direction
by turning the base.
(4) Tighten the screws.
●
Installation hole
Buzzer : Sounds intermittently 3 times.
(1)
(2)
(3)
⑤
⑦
⑧
⑨
⑥
(1)
(2)
(3)
※
※
※
1 sec.
6 sec.
15 sec.
30 sec.
Detection sensitivity is selectable, H or L.
1 2 3 4
FS-1000E is equipped with 3 functions which can be
used according to the application or environment.
Mode setting will be done by mode selector (dip
switch) in accordance with mode setting chart on
the back side of sensor unit.
(2) Mode setting
Alarm sound (buzzer)
Buzzer can be off by mode selector No.1,
SET
ON
OFF
When the ultraviolet rays of a flame is weak (it is related to size
of flame and distance to sensor), alarm initiation may be delayed
beyond the set time.
The ultraviolet rays are not visible, and may be detected from
unexpected object.
When the sensor's operation is not stable (it detects something
but not a flame) and its cause can not be identified, set detection
time longer by one step and see the course.
※
※
Application and installation
●
For the quick detection of the flame of lighter
/ match at no smoking zone.
●
Fire detection
●
In case of uncertain operation on the above
●
Fire detection in an area that may be
influenced by uncertain external light
※
When the setting is OFF Buzzer of “Low battery alarm” and
“powr on notic” are also off.
