background image

36

If the water in the basin is drained rapidly, the gasket of 

the drain cap may be deteriorated. Drain cap should be 

considered consumable goods. Be sure to replace this 

immediately. [See page 28]

Replace the accessory mohair tape according to the 

attached operating instructions for mohair tape. 

Contact your local Takara Belmont dealer if the 

movement of the shower hose is not smooth after 

replacement of the mohair tape.

This may cause device malfunction or difficulty in 

removing stains. Be sure to immediately wipe off any 

water or chemicals adhered to the areas other than the 

inside of the basin.

Remove any hair accumulated in the hair catcher. 

[See page 27]

Water leakage may be present inside the device. Open 

the maintenance cover and check the inside.

[See page 32] If the water is leaking from the pipes, 

close the taps on the cold and hot water pipes immedi-

ately [See page 32], discontinue use, and contact your 

local Takara Belmont dealer.

This may cause pain or stains on the customer's neck 

and head. Neck cushions and head pillows should be 

considered consumable goods. Contact your local 

Takara Belmont dealer to replace this immediately.

If the odor remains after cleaning the sponge, the 

sponge should be replaced. Be sure to replace this 

immediately. [Page 30]

Can the basin be 

filled with water?

Is the mohair tape 

deteriorated?

Are the areas other 

than the inside of 

the basin wet with 

water or chemicals?

Is there a foreign 

odor in the basin 

drainage?

Is the floor around 

the maintenance 

cover and the side 

panel wet with 

water?

Is the neck cushion 

and head pillow 

deteriorated?

Is there a foreign 

odor in the shower 

head holder?

Close the drainage with drain cap 

and fill with water to see if any 

water leaks out.

Check the mohair tape for peeling, 

significant staining, and deterio-

ration

Check that the areas other than 

the inside of the basin are not wet 

with water or chemicals.

Check for any foreign odor in the 

basin drainage.

Visually check the floor around the 

maintenance cover and the side 

panel for any spilled water.

Check for any tears, stains, and 

collapsing on the surface of the 

neck cushion and head pillow.

Check for any foreign odor in the 

shower head holder.

Inspection item

Inspection method

Inspection result and action to take in case of failure

Daily Inspection

Remove any objects blocking the drainage. If the 

drainage is blocked, accidental release of water or 

slight output of water due to the nighttime increase in 

water pressure may cause the water to spill out of the 

basin and lead to water leakage accidents.

Turn the tap fully to stop the water completely. If the 

water is not stopped fully, there may be abnormalities 

in the tap. Close the taps on the cold and hot water 

pipes immediately [see page 32] and contact your local 

Takara Belmont dealer.

Is the drainage 

blocked?

Is the tap closed 

tightly?

Check that the drainage is blocked 

with drain cap, towel, or 

hairdressing gown.

Turn the tap clockwise fully to 

check that the water has stopped 

completely.

Inspection item

Inspection method

Inspection result and action to take in case of failure

Be sure to inspect the following items after finishing work every day

Summary of Contents for W SWING YUME









































Reviews: