background image

21

Layout Drawing (Standard spec.)

Notes on the floor finished with tiles or glass

In the case where the floor is finished with tiles etc., screwing bolts into the floor when 
installing the shampoo unit may cause a crack on the floor surface. Change the material of the 
floor of the installation position to plywood, mortar, etc.
1 Mark the floor at the base outline and the chair mount frame installation position. Cut the tile 

or glass along the outer edge of the pattern you traced on the floor. Remove the area of tile 
or glass precisely over the installation position. 

2 Place the plywood on the area where the tile or glass was removed. The floor height of the 

plywood portion must be higher than that of the tile or glass portion. (2 to 3 mm)

215

60

35

100

214 (Mount base width)

180

160

Chair mount frame installation dim.

514

65

(Chair mount frame installation dim.)

300 (Mount base length)

17

30

60

155

140

400

Chair side

Bowl side

Standard fixing position (4 points)

Floor cut out area

100 x 180

Distance to the w

all or the fur

niture

etc.:

 Min.

 1200 mm

 (including the space necessar

when the leg rest is used.)  

 

Distance to the wall or 
the furniture, etc.: 

Min. 760 mm

(including working space 
600 mm)

Distance to the wall or the 
furniture, etc.: 

Min. 965 mm

(including working space 600 mm)

Distance to the wall or the 
furniture, etc.: 
Right Min. 400 mm; 
Left Min. 750 mm 
(including walkway 500 mm)

Co

ver outline

Chair mount frame floor fixing hole (2 points)

Spare fixing hole

Spare fixing hole

Bolt (anchor) fixing position

Bolt (anchor) fixing position

Bolt (anchor) fixing position

Bolt (anchor) fixing position

Bolt (anchor) fixing position

Bolt (anchor) fixing position 

40

Hot w

ater

1/2" 13 m/m (Raising height 80 mm)

Cold w

ater

1/2" 13 m/m  (Raising  height 110 mm)

Drain 

VU40

(Raising height  90 mm)

Center of drain

10

35

30

* Spare fixing hole

When tapping the anchor bolt (or hex 
tapping bolt) in the spare fixing hole in 
the mount base, check the plumbing 
layout beforehand. Ensure there are no 
pipes below this area. 

* not available for NRS Separate Type

750

Summary of Contents for AY-NRS2B-W

























Reviews: