Takara Belmont AY-NRS2B-W Installation Manual Download Page 2

2

Before Installation

 

Plumbing

This section includes important information about plumbing. 
Please understand the content fully for proper plumbing.

• Please follow the "Notes in plumbing" when plumbing. If not followed, the water mixing may not 

work properly and hot water of specific temperatures will not come out. 

• This product is designed for the use indoors.

 

Notes in plumbing

Do NOT use a material which rusts easily for water supply pipes.
Use VP pipes or other designated material in your area as a standard.
Use deacidified cupper pipes for hot water supply pipes as a standard.
Use the pipes of same diameter and for same pressure for both hot water supply and 
cold water supply pipes.
Ream the cut face of the pipes to clear the face of burrs.
Avoid using a reverse U-shape pipe. This may cause air trapping.
Plumbing refuses, dust, sand or oil in the hot water supply pipe and cold water supply 
pipe may cause trouble. Remove them before connecting pipes.
After plumbing and a flow test are completed, clean the strainer and the shower head.
Adjust the inclination of the drain pipe to be at least 1/50 for the pipe of    100 or less, 
and at least 1/100 for the pipe of    100 or more.
Do not mix up the cold water supply pipes and the hot water supply pipes. Connect the 
pipes in the correct combination. 
Arrange the hot water supply line in a shortest distance from the water heater so as to 
minimize the resistance. With longer distance, temperature of hot water may fluctuate or 
water amount may be reduced.
Cover the pipes with heat insulating material after plumbing completed.

Plumbing particulars for boiler
• Main pipes of same diameter and for same pressure must be used for both hot water 

supply and cold water supply as a standard.

• A boiler must be installed by a qualified installer.

This product is equipped with a deodorant trap.

CAUTION

This mark warns the user that "improper use may cause personal injuries or material damages". 

 Definition of markings

These  markings  indicate  important  information  to  avoid  personal  injuries,  or  property  damages 
against you or your customers by using this product correctly. All instructions are important for safety 
operation. Please be sure to observe them.

Summary of Contents for AY-NRS2B-W

























Reviews: