Please contact the distributor when disposing.
Have the manufacturer perform maintenance and inspection every 2 years (with fee).
【
Manufacturer maintenance & inspection
】
Disposal
5
-
9
Charging
Wearing
Lighting
After Use
Check 1
Check 2
1
.
Take out the calibration kit from the storage
bag/hard case, and place it on a desk.
4
.
Set the illumination position adjustment lever
into the indentation (front) of the pedestal.
5
.
Refer to the figure in step 3 and align the
edges of the heat sink and post (
★
mark).
6
.
Slowly press the main unit straight down until
the back hub goes into the indentation (back).
7
.
Remove the main unit from the calibration kit.
8
.
Firmly push the calibration kit to the
bottom of the storage bag/hard case
and return it to the original position.
2
.
Rotate the size adjustment knob on the main
unit clockwise and set the size to
“
smallest
”
.
3
.
Hold the sides of the light source unit
with both hands, and place the main
unit on the calibration kit.
Charging
Wearing
Lighting
After Use
Check 1
Check 2
Maintenance
5
-
8
Replace consumable parts at appropriate times.
Please see for the list of consumable parts available for purchase.
【
Replacing Consumable Parts
】
When cleaning, disconnect the connection cord.
It may cause failure.
Do not wash it by exposing it to or submerging it in water.
It may cause electric shock or failure.
When cleaning, use ethanol for disinfection.
Using detergent or disinfectants other than ethanol for disinfection may cause damage, discoloration, or failure.
Do not sterilize.
It may cause failure or damage.
Battery unit
Antibacterial urethane pad
Cord clip
2 years after purchase
When deterioration or stains become noticeable.
When it is damaged or peeled off.
Consumable parts
Approximate time of replacement
*To replace, refer to
“
Proper attachment of the antibacterial urethane pad
”
.
*To replace, refer to
“
Proper attachment of the cord clip
”
.
【
Cleaning
】
•
Wipe the transparent cover of the light source unit with a soft cloth after every use. When
the inner side of the light source unit transparent cover is dirty, contact the distributor.
•
Check that the main unit and battery unit have cooled down to normal temperature, and wipe
them with a soft cloth moisturized with a small amount of ethanol for disinfection as necessary.
•
If dirt on the attached belt or its smell bothers you, clean it while referring to the following.
•
When the storage bag is dirty, gently wipe it with a cloth slightly damp with a neutral detergent.
•
When the hard case is dirty, wipe it with mild soap and water and a soft sponge. Do not use
any type of brush that will scratch the surface.
◆
Do not dry clean.
◆
You can use very gentle wet cleaning.
◆
Use neutral detergents.
◆
Do not use fabric softeners.
◆
Wash by hand instead of using a washing machine.
◆
Do not use bleach.
◆
Do not tumble dry.
◆
Avoid direct sunlight and hang dry in the shade.
◆
Do not iron.
When you cannot wear the product
properly because the height of the
heat sink is low, calibrate the height
of the heat sink with the following
procedure.
【
Calibrating the heat sink
height
】
Indentation (back)
Indentation (front)
Pedestal
Part names of the
calibration kit
Size adjustment
knob
Post
Back hub
Back hub
Heat sink
Light source unit
Illumination range
adjustment
Indentation (front)
Before calibration
After calibration
Post
Pedestal
*It is normal for the back hub to rise from
the pedestal when you let go.
The height of the heat sink is calibrated.
CAUTION
NOTICE
3. Composition
22
23
Maintenance
Maintenance
Please contact the distributor when disposing.
Have the manufacturer perform maintenance and inspection every 2 years (with fee).
【
Manufacturer maintenance & inspection
】
Disposal
5
-
9
Charging
Wearing
Lighting
After Use
Check 1
Check 2
1
.
Take out the calibration kit from the storage
bag/hard case, and place it on a desk.
4
.
Set the illumination position adjustment lever
into the indentation (front) of the pedestal.
5
.
Refer to the figure in step 3 and align the
edges of the heat sink and post (
★
mark).
6
.
Slowly press the main unit straight down until
the back hub goes into the indentation (back).
7
.
Remove the main unit from the calibration kit.
8
.
Firmly push the calibration kit to the
bottom of the storage bag/hard case
and return it to the original position.
2
.
Rotate the size adjustment knob on the main
unit clockwise and set the size to
“
smallest
”
.
3
.
Hold the sides of the light source unit
with both hands, and place the main
unit on the calibration kit.
Charging
Wearing
Lighting
After Use
Check 1
Check 2
Maintenance
5
-
8
Replace consumable parts at appropriate times.
Please see for the list of consumable parts available for purchase.
【
Replacing Consumable Parts
】
When cleaning, disconnect the connection cord.
It may cause failure.
Do not wash it by exposing it to or submerging it in water.
It may cause electric shock or failure.
When cleaning, use ethanol for disinfection.
Using detergent or disinfectants other than ethanol for disinfection may cause damage, discoloration, or failure.
Do not sterilize.
It may cause failure or damage.
Battery unit
Antibacterial urethane pad
Cord clip
2 years after purchase
When deterioration or stains become noticeable.
When it is damaged or peeled off.
Consumable parts
Approximate time of replacement
*To replace, refer to
“
Proper attachment of the antibacterial urethane pad
”
.
*To replace, refer to
“
Proper attachment of the cord clip
”
.
【
Cleaning
】
•
Wipe the transparent cover of the light source unit with a soft cloth after every use. When
the inner side of the light source unit transparent cover is dirty, contact the distributor.
•
Check that the main unit and battery unit have cooled down to normal temperature, and wipe
them with a soft cloth moisturized with a small amount of ethanol for disinfection as necessary.
•
If dirt on the attached belt or its smell bothers you, clean it while referring to the following.
•
When the storage bag is dirty, gently wipe it with a cloth slightly damp with a neutral detergent.
•
When the hard case is dirty, wipe it with mild soap and water and a soft sponge. Do not use
any type of brush that will scratch the surface.
◆
Do not dry clean.
◆
You can use very gentle wet cleaning.
◆
Use neutral detergents.
◆
Do not use fabric softeners.
◆
Wash by hand instead of using a washing machine.
◆
Do not use bleach.
◆
Do not tumble dry.
◆
Avoid direct sunlight and hang dry in the shade.
◆
Do not iron.
When you cannot wear the product
properly because the height of the
heat sink is low, calibrate the height
of the heat sink with the following
procedure.
【
Calibrating the heat sink
height
】
Indentation (back)
Indentation (front)
Pedestal
Part names of the
calibration kit
Size adjustment
knob
Post
Back hub
Back hub
Heat sink
Light source unit
Illumination range
adjustment
Indentation (front)
Before calibration
After calibration
Post
Pedestal
*It is normal for the back hub to rise from
the pedestal when you let go.
The height of the heat sink is calibrated.
CAUTION
NOTICE
3. Composition
22
23
Maintenance
Maintenance
