background image

2

Important Safety Information

Important Safety 
Information

Please read these warnings before using your T2009 power 
supply.

Warning: Safe Operation

To reduce the risk of fire or electric shock, please adhere to 
these warnings:

Moisture: Do not expose this appliance to rain or moisture.

Cleaning: Unplug the power supply from the mains power 
outlet before cleaning. Switching it off will not reduce this 
risk.

Ventilation: Place the power supply in an area that will 
allow air to flow freely around the unit. This will prevent the 
power supply and mobile radio from overheating. Do not 
block or obstruct any of the ventilation openings on the 
unit.

Warning: Electrical Connections

To reduce the risk of fire or electric shock, please adhere to 
these warnings:

Do not operate two or more units in parallel.

Your power supply should be properly connected and 
grounded. Use the provided AC power cable to connect it to 
a mains power outlet that is properly installed and 
grounded, in accordance with all local codes and ordi-
nances. If the power supply cord is damaged, it must be 
replaced with the same type to comply with safety require-
ments.

Never alter the provided AC cable or plug. If the plug does 
not fit into the outlet, have a proper outlet installed by a 
certified electrician.

Use an extension cord only when absolutely necessary. The 
extension cord must have the same voltage and power rat-
ing as the original power supply plug. Make sure that the 

Summary of Contents for TMAA12





















Reviews: