background image

 CNC-110A Series  C-03/C-13 User's manual

 

13

 

 

 

έᚊ࿪ཝҋજ̼ѣࢨ̳Φ

 

 

TAILY AUTOMATION CO.,LTD.

 

11.1.Requirement and Safety precautions 

1. The controller should be operated in an environment that is protected from moisture, corrosive 

gases, or liquid, and free from airborne dust, metallic particles, and magnetic noise. 

2. Make sure that the power source supplies the correct voltage and is capable of supplying the 

required current to the controllers.

 

3. Do not connect or disconnect wires and connectors while power is applied to the controller. 

4. Make sure the machine and controllers are properly grounded.

 

5. Make sure that the leads and connectors are connected correctly. 

6. Normally operate under 5

 ~ 50

 environment, over 40

 should perform under good 

ventilation, avoid heating. 

11.2.Periodically maintain 

The following parts must be maintained or changed periodically as list below. If any part is found 

faulty, it must be changed immediately even when it has not yet reached the end of its life, which 

depends on the operating method and environmental condition. For parts replacement, please 

contact your sales representative. 

NO 

Part name 

Life guideline 

 1 

Winding spindles Turns counter 

CNTB-03B/03C

   

2 years 

 2 

RELAY

 (

RY-BLY

board, it used to switching the winding 

direction) 

100,000 times 

Carbon

 BRUSH

 in the DC motor 

1 years 

Summary of Contents for CNC-110A Series
















Reviews: