background image

 

 
 

 

special attention to codes for air gaps and anti-siphon devices.  

 

IMPORTANT: 

Never insert a drain line directly into a drain, sewer line, or trap. Always  allow an air gap 

between  the  drain  line  and  the  wastewater  to  prevent  the  possibility  of  sewage  being 

back-siphoned into the  conditioner. 

 

BRINE TANK CONNECTION: Install a 3/8" O.D. polyethylene tube from the Refill Elbow to the Brine Valve in 

the brine tank. 

 

OVERFLOW LINE CONNECTION: 

AN  OVERFLOW  DRAIN  LINE  IS  RECOMMENDED  WHERE  A  BRINE  OVERFLOW  COULD  DAMAGE 

FURNISH- INGS OR THE BUILDING STRUCTURE. 

Your softener is equipped with a brine tank safety float which greatly reduces the chance of an accidental 

brine overflow. In the event of a malfunction, however, an OVERFLOW LINE CONNECTION will direct the 

“overflow” to the drain instead of spilling on the floor where it could cause considerable damage. This fitting 

should be on the side of the cabinet or the brine tank. 

To connect overflow fitting, locate hole in side of brine tank. Insert overflow fitting into tank and tighten with 

plastic thumb nut and gasket from the inside. Attach a length of ½" (1.3 cm) I.D. tubing (not supplied) to 

fitting and run to drain. Do not elevate overflow line higher than 3" (7.6 cm) below bottom of overflow fitting. 

Do not “tie” this tube into the drain line of the control valve. Overflow line must be a direct, separate line from 

overflow fitting to drain, sewer, or tub. Allow an air gap as per the drain line instructions.  

 

IMPORTANT: 

Never  insert  a  drain  line  directly  into  a  drain, sewer  line,  or  trap. Always  allow  an  air  gap 

between  the  drain  line  and  the  wastewater  to  prevent  the  possibility  of  sewage  being 

back-siphoned into the  conditioner. 

 

INSTALLER SETTINGS 

 

Step 1I – Press NEXT and UP simultaneously for 3 seconds. 

 

 

 

 

 

Step 2I – Hardness: Set the amount of hardness in grains of hardness as calcium 

carbonate per gallon using DOWN or UP. The default is 20 with value ranges from 1 to 

150 in 1 grain increments. Note: The grains per gallon can be increased if soluble iron 

needs to be reduced. This display will not show if “FILTERING” is selected in Step 2F 

or if “AUTO” is not selected in Set Volume Capacity in Softener System Setup. Press 

NEXT to go to Step 3I. Press REGEN to exit Installer Display Settings. 

 

 

 

 

Step  3I  –  Day  Override: When  volume  capacity  is  set  to  “OFF”,  sets the number  of 

days between regenerations. When volume capacity is set to “AUTO” or to a number, 

sets  the  maximum  number  of  days  between  regenerations.  If  value  set  to  “OFF”, 

regeneration  initiation  is  based  solely  on  volume  used.  If  value  is  set  as  a  number 

(allowable range from 1 to 28) a regeneration initiation will be called for on that day 

even  if  sufficient  volume  of  water  were  not  used to  call  for  a  regeneration.  Set  Day 

Override using DOWN or UP:  

  number of days between regeneration (1 to 28); or 

  “OFF” 

See Setting Options Table for more detail on setup. Press NEXT to go to Step 4I. 

Press REGEN to return to previous step. 

 

Step 4I – Next Regeneration Time (hour): Set the hour of day for regeneration using 

DOWN or UP. AM/PM toggles after 12. The default time is 2:00 AM. This display will 

show  “REGEN  IMMEDIATE  ON  ZERO  GAL”  if  “IMMEDIATE”  is  selected  in  Set 

Regeneration Time Option in Softener System Setup Step 9S. Press NEXT to go to 

Step 5I. Press REGEN to return to previous step. 

 

 

 

 

 

Summary of Contents for T../MA-ANJ series

























Reviews: