background image

__________________________________________________________________________________________________________________ 
 
TAGLab  

                                                                                                                                                                                   Battery Charger | 

C4

 

 

Make sure that the acid of the battery does not come into contact with the skin or clothing as it may cause 

burns. However, if this happens then rinse the affected area immediately with water and contact your 

physician immediately. Never trip the battery as acid may leak. Always wear safety goggles and protective 

gloves.  

 

Store the charger in a dry place (imperatively away from dampness). Protect from liquid, rain and snow. 

 

Do not place the battery on top of the charger or vice versa. Do not place other equipment on top of the 

charger. 

 

Do not allow the two clamps from the charging cable to touch when the charger is on. Only touch the 

insulated part of the terminals 

(-)

 and 

(+)

 

Do not connect the clamps or the battery poles through conductive tools or objects. 

 

Never use the charger when it has undergone a violent shock or fall. In this case, have the appliance 

inspected and repaired by a qualified technician. 

 

Position the electrical cable of the charger so that no one can walk on top of it. Set up the charger as far 

away from battery as the charging cable allows. Ensure that all plugs and cables are free of moisture. Never 

connect the device to the mains with wet or moist hands. Do not pull on the electrical cable or charging cable 

to prevent damaging the charger. The charging cable must never make contact with any fuel pipes e.g. 

gasoline pipes. 

 

Do not pour liquid on the charger as there is a risk of electrocution. Never cover the charger when the device 

is in operation. Make sure there is no risk of explosive or flammable substances e.g. gasoline or solvent, 

being ignited whilst using the charger. 

 

Do not expose to heat or an excessive source of light. Keep the charger away from naked flames, hot 

surfaces and sparks. Stop using the device immediately if you notice smoke or an unusual odour.  

 

Make sure the mains supply has been disconnected before performing battery charger installation, 

maintenance and upkeep work. 

 

Never disassemble the charger or attempt to repair the device. For inspection and repair, take it to a 

qualified technician. Remove all device cables from the battery before attempting to drive your vehicle.  

 

Warning  

Life-threatening danger to infants and children! Never leave children unsupervised with the packing material as this 

can cause suffocation. Do not allow children to play with cables – strangulation hazard. Do not allow children to play 

with the components or fasteners, as they could be swallowed and result in suffocation. 

The manufacturer is not responsible for damages caused by: 

 

Improper connection and / or operation. 

 

Exterior force, damage to the device and / or damage to parts of the device caused by mechanical impact or 

overload. 

 

Any type of modification to the device. 

 

Use of the device for purposes that are not described in this instruction manual. 

Summary of Contents for C4


















Reviews: