manualshive.com logo in svg

tae TA-100/6P, Instruction And Operation Manual, Page: 7 / 10

Share
Download
tae TA-100/6P Instruction And Operation Manual Download Page 7

7

missprints and technical changes reserved

Instruction & Operating Manual

TA-15/6P...200/6P

Drive does not run when switched to "DRIVE

ON"

6.1 Fault location

Symptom

LED 8 (Power on) does not light up.

+/- 15V (LED 5, LED 2) does not light up.

Possible causes

a) Defective fuse Si 1 on the upper PC-board
b) One phase is missing
c) No supply voltage (115V) for relays d1 and d2.

Check voltage (115V) between terminals 9 and

16

d) LED 8 or D37 defect.

a) One phase is missing
b) Check power supply, m/- 24V

a) Motor load too high.
b) Drive operates at the current limit, LED 6 lights

up.

c) Current limit is adjusted too low, drive switches

off after short operation.

d) Defective speed potentiometer.

a) Check switch-on contact (terminals 1 and 9)
b) Defective fuse Si 1 on the upper PC-board
c) LED 8 (Power on) does not light up
d) LED 9 does not light up however LED 11 lights

up, jumper or quick-stop contacts terminals 24

and 25 not closed.

e) No reference voltage (terminal 2) voltage is

variable by speed potentiometer from 0 to 10V

f) Relay d6 (malfunction) not energised. LED 3,

red, lights up. Confirmation of malfunction is

only possible if LED 4 and LED 6 do not light

up and if the field control is not activated.

g) Check three phase line input.
h) Defective fuses Si 1, Si 2 or Si 3 on lower PC-

board.

i) Check field voltage and field current.

a) I x R compensation P3 is set too high.
b) Defective tachometer or tachometer leads.
c) Stability potentiometer P8 is wrong adjusted.
d) Auxiliary winding of the d.c. motor is wrong

connected

e) Triggerinig of one Thyristor temporarely

interrupted.

Output voltage does not increase when

speed potentiometer is turned up

Drive does not run stable

Summary of Contents for TA-100/6P











Reviews:

No comments