manualshive.com logo in svg

tae TA-100/6P, Instruction And Operation Manual, Page: 3 / 10

Share
Download
tae TA-100/6P Instruction And Operation Manual Download Page 3

3

missprints and technical changes reserved

Instruction & Operating Manual

TA-15/6P...200/6P

Terminal 7 and 8

Terminals for contacts of all malfunction signals. (Contacts open in event of fault)

Terminal 2, 5, 6

Speed potentiometer

With this potentiometer the speed is infinite variable from minimum to maximum

speed.
Poti-connect: KL. 5 = Beginning

KL. 6 = End

KL. 2 = Connect center

Terminal 13

Current reference signal output

Terminal 18

Current reference signal input

Terminal 13 and 18

For speed control these terminals must be jumpered

Terminal 17

Reference signal (negative) 0-max. 200V

depending on value of resistor R83

General input voltage 0-10V

Terminal 19 and 20

Terminals for connection of a.c. tachometer

Output voltage of tachometer approximately 100-150V at rated motor speed.

r

When tachometer feedback is utilized jumpers 

I

 and 

VII

 and resistor R82 must

be removed.

r

Jumpers 

IX

 and 

X

 must be installed and jumper 

VIII

 must be removed.

r

The adaption of the tachometer signal is achived by changing the value of

resistor R91.

Terminal 11 and 20

Terminals for connection of d.c. tachometer
KL. 11 = Negative
KL. 20 = Positive

r

Jumpers 

IX

 and 

X

 must be removed and jumper 

VIII

 must be installed.

r

The adaption of the tachometer signal is achieved by changing the value of

resistor R91.
R91 is calculated as follows:
R91 in kOhm = tachometer voltage at rated motor speed minus 50

Terminal 22 and 23

Relay contacts (normally open, no potential)

(for operation of auxiliary armature solenoid.)

Terminal 24 and 25

Terminals for quick-stop (normally closed)

Terminal L1 and N

Terminals for connection of fan 230V VAC, 50/60Hz at TA-60/6P

2.3 Terminal Strip KL. 2

 (Only at TA-40/6P available)

Terminal 3 and 4

Terminals for connection of fan 230V VAC, 50/60Hz

Summary of Contents for TA-100/6P











Reviews:

No comments