21
English
Symptom
Possible cause
Remedy
No sound is produced
for USB input.
'
The computer is set to a different input
component.
'
The computer’s mute function is ON.
Check the computer’s sound settings.
'
Connections are wrong.
'
The unit is not detected by the computer.
'
After the unit is connected to the computer,
if the unit’s input is switched to USB, the
computer’s sound setting may switch to
a different input component. In this case,
reselect TAD-USB1 ver2 or TAD-USB2 ver2 as
the input.
'
Check the connections again.
The file format, OS, or playback software is not
supported.
Confirm that the OS, software, and file sampling
rate are supported (page 18).
The USB input’s
sampling rate is always
the same.
Depending on the computer’s setting, the
sampling rate may remain the same even when
playback files have different sampling rates.
Check the computer settings.
Computer sounds
(other than music
sounds) are audible
from the USB input.
Depending on computer settings, the
computer’s boot-up beeps or error sounds may
be audible from the unit.
Check the computer settings.
When input is set to
something other than
USB, the unit can’t
play music files on the
computer’s playback
software.
When not set to USB input, the computer
doesn’t recognize the unit.
Switch to USB input, and reset the computer’s
sound setting to TAD-USB1 ver2 or TAD-USB2
ver2.
The power turns off by
itself.
If the ECO (power-saving) mode is turned ON,
the unit will automatically enter standby mode
if no operation is performed on the unit for 30
minutes.
Set the ECO (power-saving) mode to OFF
(page 19).
Display is not visible.
The display viewing angle is within 45° to right/
left from the front of the unit.
View the display from immediately in front of the
unit.
The unit is set to display off.
Press the
DISP OFF
button on the main unit (or
the
DISPLAY OFF
button on remote control) to
cancel the display off function.
The remote control
doesn’t work.
'
The remote control’s batteries are expended.
'
The remote control is being used too far
away from the main unit.
'
Angle is bad.
'
Line of sight to the main unit is blocked.
'
Strong light from a fluorescent lamp or
other light source is directly striking the
signal receiver.
'
Replace the batteries with new ones.
'
Use the remote control from within a distance
of 7 meters (23 ft.), and within an 30° arc to
right/left of the unit’s front panel.
'
Remove obstacles between the main unit
and remote control, or change to a different
location when operating the remote control.
'
Readjust the position of lamps or other light
sources so that strong light does not strike the
signal receiver.
Static electricity or other external influences may cause malfunctioning of this unit. In this case, unplug the power cord and
then plug back in. This will usually reset the unit for proper operation. If this does not correct the problem, please consult your
dealer.
This unit is designed as a consumer audio product (audio/video component). It is not designed for long continuous
use as a commercial BGM source, nor for use in automobiles, ships, or outdoors.
Summary of Contents for TAD-D1000TX
