background image

10

Choosing Where To Place The Loudspeakers

Loudspeaker placement within the listening room will have a great impact upon the total performance of TAD Reference One loudspeakers 
in terms of bass performance, tonal accuracy, and imaging. All rooms are different and so this section is intended as a guide only. Experi-
mentation in your room will yield optimum results.
Begin by placing the rear of the loudspeakers approximately one to two feet in from the front walls and the sides one to two feet in from 
the side walls of your listening room, as shown in Figure 7. Your listening position should be roughly equal to the distance between the two 
loudspeakers. Also, turn the loudspeakers inward so each axis points toward the listening position.
Next, connect the audio system as described in CONNECTING THE SPEAKERS on page 12. Then, optimize the loudspeaker placement as 
described in OPTIMIZING THE SYSTEM on page 16.

 

WARNING!

Keeping the spikes inserted can cause damage to the bottom of the unit in the event that you move the loudspeaker. Be sure to 
remove the spikes before moving the loudspeaker to another location.
In order to protect the bottom of the unit from damage when moving the loudspeaker, you should place a thick cloth or mat 
beneath the system before moving it to a new location.

Precautions regarding the installation location

Do not install the speaker system in areas exposed to direct sunlight nor near heating appliances. Such conditions may 
result in shrinkage of the wood materials and finish, leading to deformation of the enclosure, discoloration, or damage 
to the speakers.
Conditions considered unpleasant by humans are detrimental to speakers as well. Providing a comfortable environment 
for the speakers will assist them in demonstrating their best performance.
Please maintain the usage environment as follows:
Temperature :    

15 ºC to 25 ºC (59 ºF to 77 ºF)

Relative Humidity :  

35 % to 65 % (winter)

 

 

 

40 % to 70 % (summer)

 

When using room air-conditioners or stoves to rapidly cool or heat room spaces, take precautions to avoid excessive 
dehumidification. 

 

Avoid placing the speaker near areas such as windows, as outside air can cause condensation to occur within the 
speaker.

Summary of Contents for Reference One





















Reviews: