Tab T9-Pro Product User Manual Download Page 5

2

Safety instruction

14. Please clean according to the instructions of the detergent. If a large amount of clean-

ing solution is added, more foam will be generated during use, which may penetrate into 

the motor and cause danger. It is recommended to use the detergent produced by our 

company and the manufacturer approved by our company, and it must not contain acid, 

alkali solution or substances harmful to the environment.

15.  Please  keep  the  detergent  out  of  the  reach  of  children.  If  the  cleaning  solution 

accidentally enters the eyes, rinse thoroughly with clean water; if you accidentally eat, you 

should seek medical attention immediately.

16. Please do not disassemble the closed machine by yourself. There are no parts in the 

machine that customers can repair by themselves, and do not try to change the perfor-

mance of the machine, otherwise it will lead to danger.

17. Please do not use the voltage that does not correspond to the specifications of this 

product, otherwise it will damage the motor, and it is more likely to hurt the users.

18. Please do not shake the machine up and down or collide violently, and do not tilt the 

machine to one side or lay flat to prevent sewage from flowing into the motor.

19. The main body and floor brush of this product contain electrical components, which 

should not be soaked in water or washed, otherwise fire and electric shock accidents may 

occur due to short circuit of the machine.

20. It is forbidden to use this product without installing the rolling brush, clean-water tank, 

dirty-water tank and filter element.

21. Please make sure to replace the rolling brush after turning off the machine.

22.  After  using  the  machine,  please  clean  up  the  dirty-water  tank  in  time  to  keep  the 

ventilation path unblocked, so as to avoid the suction drop and motor heating caused by 

blockage, thus affecting the service life of the machine.

23.  After  using  the  machine,  please  keep  it  in  a  dry  place.  Humid  places  will  affect  the 

insulation and service life of electrical appliances.

24. In order to prevent tripping, the machine should be placed against the wall after use.

25. Please check the smoothness of the suction nozzle regularly. If there is any blockage, 

please clear it in time, so as to avoid the decrease of suction caused by blockage and 

affect the service performance of the machine.

26.  When  the  machine  breaks  down,  please  do  not  repair  it  yourself.  Please  call  the 

after-sales department of our company for help.

Summary of Contents for T9-Pro





















Reviews: