background image

General

General

We strongly recommend that you read this user manual before using LineCrypt.

Deutsche Telekom cannot be held liable for any possible damage caused to

the device or other facilities arising from the failure to follow the instructions in

this manual. 

Overview of pictorial symbols

Safety symbol to warn against danger for people and property is identified with

a triangular warning sign.  

Important messages for data security are identified with the hand icon.

Important messages for operation of the LineCrypt DSL are identified with the

bulb icon.

Safety notes

Do not open the LineCrypt. By opening the four screws on the base of the

housing you may endanger the user and any warranty claim will be waived.

Allow no liquids to seep into the LineCrypt.

Assemble the device as described in the section “Assembly”.

Do not plug in or detach any connections to the LineCrypt during a thunder-

storm.

The LineCrypt is only intended for use in dry indoor areas. 

Lay the cables in such a way that they cannot be stood on or tripped over by

anyone.

Before any maintenance work on the LineCrypt pull out the mains plug. 

3

Summary of Contents for LineCrypt DSL






















Reviews: