background image

English

To perform electrical wiring of the unit, please refer to the wiring diagram pasted on the unit 

casing.

Caution

13

VH

WARNING

Before carrying out any work on the equipment, 

make sure that the electrical power supply is 

disconnected and that there is no possibility 

of the unit being started inadvertently.
Non-compliance with the above instructions 

can lead to injury or death by electrocution.

9. ELECTRICAL CONNECTIONS

SEE APPENDIX

IMPORTANT

Short circuit protection shall be provided. This protection shall comprise fuses or circuit breakers with high 

breaking capacity, mounted on the distribution board.

 

²

Fuse available as an option

 

²

Cable not supplied

The electrical installation must be performed by a fully qualified electrician, and in accordance with local 

electrical standards and the wiring diagram corresponding to the unit model.
Any modification performed without our prior authorisation may result in the unit’s warranty being declared 

null and void.
The power supply cable section must be sufficient to provide the appropriate voltage to the unit’s power 

supply terminals, both at start-up and under full load operating conditions.

All fan coil units are designed for operation under 230 volts, single phase, 50 or 60 cycles .
A voltage variation of ± 10 % with regard to nominal voltage 230 V is acceptable.

Before making the connections, be sure that the available power supply has the same voltage and phase as 

that shown on the fan coil unit nameplate.
Line and low voltage wiring must be done in accordance with electrical code whichever is applicable. 

Earthing of unit is imperative.

Manufacturer or its representative cannot be held responsible for accidents resulting from incorrect or 

non-existent earthing.

A device to disconnect all the power conductors with an approved minimum opening distance must be 

included in the mains power supply according to best installation practices.

SE3931 models 

VH07/VH15/VH18/VH21/VH24/VH27 

 

230V 50Hz/60Hz +/- 10%

SE3932 models 

VH07 + Aquanet 

 

 

230V 50Hz/60Hz +/- 10%

SE3933 models 

VH15/VH18/VH21/VH24/VH27 + Aquanet   

230V 50Hz/60Hz +/- 10%

9.1. WIRING DIAGRAM AND LEGEND

9.2. POWER SUPPLY

9.3. ELECTRICAL CONNECTIONS

Summary of Contents for VH07













































Reviews: