System air 316293 Installation Manual Download Page 3

2

Ground the air conditioner.

Do not connect the ground wire to gas or water pipes, 

lightning rod or a telephone ground wire.Incomplete 

grounding may result in electric shocks.

Be sure to install an earth leakage breaker.

Failure to install an earth leakage breaker may result in 

electric shocks.

Connect the outdoor unit wires , then connect the indoor 

unit wires.

 

You are not allow to connect the air conditioner with the 

power source until wiring and piping the air conditioner is 

done.

While following the instructions in this installation 

manual, install drain piping in order to ensure proper 

drainage and insulate piping in order to prevent 

condensation.

Improper drain piping may result in water leakage and 

property damage.

The appliance is not intended for use by young children 

or infirm persons without supervision.

DISPOSAL

Do not dispose this product as unsorted 

municipal waste. Collection of such waste separately for 

special treatment is necessary.

Don't install the air conditioner in the following locations:

If refrigerant leakage occurs, ventilate the area 

immediately. 

Toxic gas may be produced if the refrigerant comes into 

contact with fire.

After completing installation, make sure  that refrigerant 

does not leak.

The appliance must be installed in accordance with 

national wiring regulations.

To install properly, please read this "installation manual" at 

first.

The air conditioner must be installed by qualified persons.

When installing the indoor unit or its tubing, please follow 

this manual as strictly as possible.

If the air conditioner is installed on a metal part of the 

building, it must be electrically insulated according to the 

relevant standards to electrical appliances.

When all the installation work is finished, please turn on 

the power only after a thorough check.

Regret for no further announcement if there is any change 

of this manual caused by product improvement.

2.    INSTALLATION INFORMATION

INSTALLATION ORDER

Select the location;

Install the indoor unit;

Install the outdoor unit;

Install the connecting pipe ;

Connect the drain pipe;

Wiring;

Test operation.

There is petrolatum existing.

There is salty air surrounding (near the coast).

There is caustic gas (the sulfide, for example) existing 

in the air (near a hot spring).

The Volt vibrates violently (in the factories).

In buses or cabinets.

In kitchen where it is full of oil gas.

There is strong electromagnetic wave existing.

There are inflammable materials or gas.

There is acid or alkaline liquid evaporating.

Other special conditions.

CAUTION

Summary of Contents for 316293













Reviews: