SYSFORM CP335B Operation Manual Download Page 8 | Manualshive

Page: 8 / 28

background image

6

The side lays and the end stop should be adjusted according to the ejecting

    situation.
    3.4 Paper press & guides.

Short Paper Press
                                                                                                                      Cylinder Side
                                                                                                                      Guide

Long Paper Press

                                                                                                                        Side Guide


    The side guides should be on proper position to hold the paper stack. The paper
    press is used to hold the paper on the top to avoid feeding failure as the top paper
    is flowing up by the blow flow. To get a smooth feeding, the blow flow, separator
    gap and stack height should be adjusted in cooperation.

    3.5 Installation of Blade
    Loosen the 2 screws on the blade gate. Push the blade all the way into the
    machine. The installation direction refers to the label on the blade gate.

«
...
6
7
8
9
10
...
»

Summary of Contents for CP335B





























Reviews:

No comments

Related manuals for CP335B

KM 130/300 R Bp

Brand: Kärcher Pages: 372

Brand: Kärcher Pages: 16

BRC 30/15 C *JP

Brand: Kärcher Pages: 48

KM 130/300 R Bp

Brand: Kärcher Pages: 27

Brand: Kärcher Pages: 11

Brand: Kärcher Pages: 16

Brand: Kärcher Pages: 4

Brand: Oki Pages: 923

Brand: Oki Pages: 1020

INSTANT FOG 1700 PRO

Brand: Cameo Pages: 64

Brand: baalbaki Pages: 8

Brand: Singer Pages: 8

Brand: Olivetti Pages: 151

Memory Craft 11000

Brand: Janome Pages: 21

Brand: PowerBoss Pages: 52

Brand: Mybelle Pages: 4

Brand: Beko Pages: 40

Brand: Beko Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands