Replacement Parts
Description
Part Number
A
B
Handle
Set Screw
RL-290
B
Set Screw
LL-27
C
Cycle Timing Washers (7)
LL-28
D
E
F
Nut
Limit Stop Washer
Limit Stop Washer, Fixed
RL-268
G
Upper Housing
LL-3N
G1
Upper Housing O-rings (3)
LL-48
G1
H3
H4
H5
H10
Upper Housing O-rings (3)
Cartridge O-ring
Cartridge O-ring
Guide O-ring
Piston Quadring
RL-272
H
Cartridge
Quick Closing Cartridge
LL-1A
LL-1B
H1
H6
Control Spindle Kit
Piston Assembly
RL-266
H2
Thrust Washer
LL-35
H6
Piston Assembly
LT-4AA
H11
Piston Spring/Cylinder
RL-267
J
0.5 gpm Vandal Resistant
Aerator Kit with Key
RL-292
K
L
Check
Spring
RL-269
R
S
T
Mounting Bracket
Spacer
Mounting Nut
SPF-KIT
W
Check/Screen Assembly
LL-71B
X1, X2
8" Deck Plate Assembly
RL-291
Y
Washer
TMX-06527-1
Parts Breakdown
B
A
C
D
E
F
G
H
I
J
K
M
L
O
N
P
Q
R
S
T
U
V
W
DO NOT
REMOVE TAPE
X1
X2
Y
Installation / Tools Required
Water lines MUST be thoroughly flushed BEFORE and AFTER installing the faucet to prevent foreign matter i.e.
copper chips, sand, stones, etc. from clogging and possibly damaging the sealing surfaces of the cartridge.
Notes:
1) Recommended minimum operating water supply pressure is 40 psi.
2) Supply stop valves must have 3/8" O.D. compression outlet.
1
2
U
V
W
1
2
3
3
Y
1) Remove compression nuts (U) and
ferrules (V) from supply stops. Re-
tain for installation to faucet copper
tubing. Ensure washer is in place
before installing. Install check/screen
assemblies (W) to supply stops.
2) Install faucet (I), threaded rods (M),
mounting gasket (Q), and 3/8" cop-
per tubing (P) to deck surface.
M
1
3
R
2
S
T
4
3) Place mounting brackets (R) and
spacers (S) onto threaded rods (M).
Secure hardware by tightening
mounting nuts (T) clockwise.
3
3
1
2
U
P
V
W
2
A
J
1
3
4
5) Remove aerator (J). Turn handle (A)
to full cold position. Open supply,
holding down handle for 10 seconds.
Rotate handle to full hot position,
open supply and repeat above
procedure. Hold down handle and
rotate from left to right to flush lines
completely.
6)
After faucet has been operated
through a number of cycles, and sup-
ply water temperature is at desired
levels, adjustments to these features
can be made (see page 4).
I
M
Q
P
Important:
DO NOT REMOVE
tape on copper tubing.
CAP AND CARTRIDGE ASSEMBLY
G1
H6
H11
G
H
H3
H4
H5
H7
H8
H9
H10
H12
H13
H14
H1
H2
Adjustable Wrench
Allen Wrench: 2.5 mm
Phillips Head Screwdriver
4) Connect compression nuts (U) and
ferrules (V) to copper tubing (P).
Carefully bend copper tubing (P) to
meet check/screen assemblies (W).
Attach compression nuts to check/
screen assemblies.
7)
Optional 8" Deck Plate:
Remove
threaded rods (M) from faucet (I).
Install two screws (X2) through
bottom of deck plate (X1) into
faucet (I). Install faucet and deck
plate to deck surface.
3
3
I
M
1
2
X2
X1
I