5
22
For a more thorough cleaning of the electronic sensor,
we advise you to use a glass of white vinegar, or a
mixture of water (70%) and descaler (30%), to be
found in supermarkets or any specialized shop. Never
use plain, undiluted descaling products! You could
chemically damage the sensor’s surface! Leave the
product or the vinegar to act on the sensor for at least
2 hours (Fig. 32).
Fasten the sensor back onto the machine, by turning
clockwise.
Tighten without forcing.
Important! The first time the machine is to be used
following this operation, remember to discharge a
little steam onto a dirty cloth. Repeat this several
times, in order to empty the steam circuit of all
descaling product.
The machine is now ready for use once again!
Important!
Before fastening the sensor, the brass
element functioning as contact with the metallic part
of the sensor must be cleaned (fig.A).
To efficaciously clean the component, we
recommend use of an antioxidant spray solution,
contributing to protection of the contact, also against
wear-and-tear.
Figure 29
Figure 30
Figure 31
Figure 32
Abb. A
Fig. A
Figura A
WARNING!
Your Vapor Cleaning System MUST BE PLUGGED INTO A GROUNDED OUTLET,
or electrical shock can occur. Check with a qualified electrician if you do not
know if the outlet is grounded.
Do not modify the plug provided with the Vapor System, if it will not fit outlet,
than have a proper outlet installed by a qualified electrician.
NOTE:
In Canada, the use of a temporary adaptor is not permitted by the Canadian
Electrical Code.
NOTE:
In the event that an extension cord is used with this System, it must be a mini-
mum of 14 gauge, 3 wire, grounded, SJ quality, 60 degree C.
THIS UNIT MUST BE GROUNDED
If the unit should malfunction or break down, grounding provides a path of least
resistance of electrical. Current to reduce the risk of electrical shock. The uniti
s equipped with a cord having an equipment grounding conductor and groun-
ding plug. The plug must be inserted into an appropriate outlet that is properly
grounded in accordance with all local codes and ordinaces.
WARNING – Improper connection of the equipment-grounding conductor can
result in a risk of electricShock. Check with a qualified electrican or service
person if you are in doubt a sto whether the outlet is Properly grounded. Do
not modify the plug provide with the appliance – if i twill not fit the outlet, have
a proper outlet installed by a qualified electrician. This units is designed for use
with a normal 110/120 volt circuit, and has a grounded plu that looks like the
Plug illustrated in sketch (A). A temporary adaptor that looks like the one illustra-
ted in stretch (B) or (C) May be used to connect the plug to a 2 pole receptable
as shown in stretch (B) if a properly grounded outlet is not available. The tempo-
rary adapter should only be used until a properly grounded outlet sketch (A) can
be installed by a qualified electrician. Whenever the adapter is used, it must be
held in place by a metal screw.
WARNING!
Clean the exterior of the machine only with a wet cloth.
Do not use solvents or detergents which could damage the plastic surface
9
GROUNDING INSTRUCTIONS
If the unit should malfunction or break down, grounding provides a path of least resistance of electrical
Current to reduce the risk of electrical shock. The uniti s equipped with a cord having an equipment grounding
conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly grounded
in accordance with all local codes and ordinaces.
WARNING – Improper connection of the equipment-grounding conductor can result in a risk of electric
Shock. Check with a qualified electrican or service person if you are in doubt a sto whether the outlet is
Properly grounded. Do not modify the plug provide with the appliance – if i twill not fit the outlet, have a
proper outlet installed by a qualified electrician.
This units is designed for use with a normal 110/120 volt circuit, and has a grounded plu that looks like the
Plug illustrated in sketch (A). A temporary adaptor that looks like the one illustrated in stretch (B) or (C)
May be used to connect the plug to a 2 pole receptable as shown in stretch (B) if a properly grounded outlet
is not available. The temporary adapter should only be used until a properly grounded outlet sketch (A) can
be installed by a qualified electrician. Whenever the adapter is used, it must be held in place by a metal screw.
