Swing-N-Slide WS 8351 Assembly Instructions Manual Download Page 61

Page: 61 / 64

STEP 48

Anchor-It

Anchor-It Strap

1-1/2” Lag

Screw

5/16” Washer

5/16’’ x 1-1/2” Lag Screw (x6)

Fold up

1. Place swing set in fi nal location and mount Anchor-It(s) at locations circled above.

2. Twist the Anchor-It into the ground until only the loop is exposed.

3. Place Anchor-It Strap thru loop, fold the ends together and attach to the unit as shown.

Note: Keep as little play as possible using any of the holes in the strap that work best.

TIP:

When installing Anchor-Its in rocky or hard soil, create a starter hole at the desired locations using either a 16’’ Concrete

Drill Bit, or a long screw driver then insert and install the Anchor-Its as shown. This will allow you to get traction with the Anchor-It

faster and allow the device to seat more securely.

Summary of Contents for WS 8351

































































Search results

Summary of Contents for WS 8351

Reviews:

Related manuals for WS 8351

Brands by name

Popular brands

Swing-N-Slide WS 8351, Assembly Instructions Manual

Search results

Summary of Contents for WS 8351

Reviews:

Related manuals for WS 8351

Brands by name

Popular brands