background image

WARNING 

LEDGE 

PLACEMENT

ENTRY POINT

VIEW FROM INSIDE THE DECK

LATCH

GATE

POST

SELF CLOSING 

HINGE

GATE

LATCH BAR

18

Using the Latch, Latch Bar and Hinges as templates, 
drill the holes in the locations as illustrated at the bottom.  

Drill a 5/32 hole for the Latch Bar and Self 
Closing Hinges. 

Drill a 7/64 hole for the Latch. 

Mount the Hinges and the Gate using 1/2” 
long Self-Tapping Screws so that the Gate 
swings on to the deck in the direction of 
the rear fence.  

Mount the Latch Bar to the Gate using 
the #10x1/2” Self-Tapping Screw. 

Mount the Latch to the Gate Post using 
#6x3/8 long Self-Tapping Screws 

(Note: the Latch mounts approximately 
21/8” from the top of the Gate).

Test the Gate to insure that it is perfectly aligned 
and closes and completely latches by itself. 

It is very important to periodically test and maintain the Gates proper functioning.

WARNING: Make sure that your pool is not accessible when not in use!!!

WARNING LABELS

With your deck you are provided with 5 additional Warning Labels.  One Large Label 
(#490090) is to be permanently affi xed to the top of the pool’s Top Ledge at the entry 
point of the pool.  The two long, thin labels (#490091) are to be affi xed on the inside of 
the pool’s Top Ledge opposite to and facing the entry point of the pool.  The two Square 
Labels (#490021) are to be affi xed on the outside edge of the deck by the outside ladder.  
To affi x these labels, simply clean the area where the label is to be applied and peel off 
the backing and press the label fi rmly into place.  Should you need any additional Labels 
for any reason, simply order them by part number from your local dealer or direct from the 
manufacturer.

15

Consumer Awareness Booklets: 

The following books are available through the APSP: 

“The Sensible Way To Enjoy Your Pool”

...published by the NSPI, October 1983 (revised September 1986), 

“Children Aren’t Waterproof”

...published by the NSPI, 

“Pool & Spa Emergency Procedures For Infants And Children”

...published by the NSPI.

Contact: APSP   •    2111 Eisenhower Avenue, Alexandria, Virginia 22314  •  (703) 838-0083

#490090

#490091

#490021

Summary of Contents for end deck



















Reviews: