background image

OVAL

POOL 

ASSEMBLY 

INSTRUCTIONS

Part# 420364-14

3 1 3   R E G I N A   AV E N U E ,   R A H WAY,   N E W   J E R S E Y   0 7 0 6 5 - 4 8 9 1

Phone: (732) 574-1500 • Fax: (732) 574-1551 • www.swimnplay.com • E-mail: [email protected]

DANGER

DO NOT DIVE OR JUMP

into your pool. Your pool is

approximately 4' deep. It is 

not designed for diving 

or jumping. If you dive or jump

into your pool you run the risk

of permanent injury or death.

Alert all visitors 

and family of

this and point

out all warning

labels supplied.

ADULT SUPERVISION REQUIRED

GENERAL

Installation of this above ground pool is not extremely hard
or confusing, but it is a big job. The secret to installing a
pool so that it will give you years of pleasure is to take the
time to follow instructions and do things right the first time.
Your pool warranty is void if these instructions are not 
followed 100%.  Read all instructions including accessories
such as filters, pumps, skimmers, decks, etc. prior to 
starting. Before you start, check to see that you have the
correct number of parts. Use your parts list which is broken
down by carton. The manufacturer reserves the right to
revise, change, or modify construction of its pools.

NOTE: If a power drill is used during installation, 
it should be a variable speed drill used on low 
setting. Torque should not exceed 39 inch pounds.

FAILURE TO COMPLY COULD RESULT IN SCREWS STRIPPING OUT.

Summary of Contents for Above Ground Swimming Pool





























Reviews: