Swim'n Play 7

SAFETY TIPS - RULES AND REGULATIONS 

• 

 

Never permit the pool to be used unless at least one person other 
than the bather is present.  Children must always be under careful 
adult 

supervision. 

• 

 

Never leave the pool open and unattended.  Remove the ladders or other means 
of entry when it is unattended.  As a further precaution, the pool should be 
covered when it will not be used for any extended period of time. 

• 

 

Do not walk on, climb on, sit on, stand on, or dive from the top seat of the pool.  It is not designed 

for this.  If you do, you run a risk of permanent injury or death from a serious fall. 

• 

 

Locate pumps and filters in such a way that children cannot climb on them and gain access to the pool. 

• 

 

If a drain or suction outlet cover is missing or broken, do not use the pool. Suction can cause body part entrapment, 
hair and jewelry entanglement, evisceration, or drowning. Repair or replace the drain or suction outlet cover before 
allowing the pool to be used. 

• 

 

Never run the filter while there are swimmers in or around the pool.  Be sure electrical hook-ups comply with national 

and Local electrical codes. 

• 

 

Do not dispense chemicals into the pool while the pool is being used.  Poisoning or painful skin irritations can occur. 

• 

 

Do not permit horseplay or dangerous water games in and around your pool.  Remember that the pool area may be 

wet and slippery, and accidents resulting in serious injuries can be prevented if rules of behavior are strictly enforced. 

• 

 

Keep the water sanitary and healthful at all times, maintain pool sanitation with the use of a good filter system and 

the regular application of water purifying chemicals.  Unsanitary water is a potential health and safety hazard. 

• 

 

Lighting should be provided to illuminate safety signs, deck surfaces, and walks during nighttime pool use. 

• 

 

Do not allow toys, chairs, tables, filtration system's pumps, heaters or other objects that a young child could climb, 

to be within four feet (4') of the pool. 

• 

 

Teach your children to swim. 

• 

 

Keep all electrical radios, speakers and other appliances away from the swimming pool. 

• 

 

Keep the deck and pool area clean and clear of objects that may create a tripping hazard. 

• 

 

When you touch the filters, pump or electrical parts, make sure the ground under your feet is "Bone Dry". 

• 

 

Face pool ladder(s) going up or down. 

• 

 

Allow only one person at a time on the pool ladder(s). 

• 

 

Instruct pool users about the proper use of all pool ladder(s) and staircases. 

Summary of Contents for 7" XL


























Reviews: