Swim'n Play 7

3 LAYERS 

OF TAPE 

CLOTH TAPE 

OR DUCT TAPE 

VIEW FROM 

INSIDE OF POOL 

WALL 

SEAM 

SKIMMER 

INLET FITTING 

SKIMMER 

RETURN FITTING 

3 LAYERS 

OF TAPE 

INSIDE OF 

POOL VIEW 

WALL 

SEAM 

EXTENDED 

END OF WALL 

EARTH MOUND 

Build earth mound on top of wall guard using screened 
damp earth or pre-washed sand.  Shape and compact earth 
mound to run 8" up from ground and 8" away from the wall. 

Do not use any material that will compress under 
pressure for the earth mound is an important part 
of the pool installation. It prevents the wall from 
lifting up and the liner from sneaking underneath 
the pool wall. Spread the remaining sand equally 
across the bottom of the pool. This will give you 
a 2“ to 3” sand base. 

Manufacturer cannot assume 

responsibility of the performance 
of this product if the earth mound 
is omitted or not properly installed. 

EARTH 

MOUND 

8” 

8” 

OPTIONAL 

WALL 

GUARD 

12” 

12” 

DANGER

 DO NOT USE ANY MATERIAL THAT 

WILL COMPRESS UNDER PRESSURE 

FOR THE EARTH MOUND. 

SEE INSTRUCTIONS TO LEFT. 

Wall guard is optional. 

Tape wall guard (plastic sheeting) to pool wall 12" up from 
ground and smooth out on ground 12" from wall.  This will 
protect your pools metal parts from chemical reactions with 
the soil used in the earth mound. 
Several  commercial products can also be used in place of 
earth mound. Consult your professional pool dealer. 

Once the wall is closed and screws and nuts are 
tightened securely, cover the screw heads on the 
inside of the pool with 3 layers of cloth tape all the way 

RECHECKING YOUR WORK 

POOL WALL 

VIEWED FROM 

ABOVE 

RADIUS 

CENTER STAKE 

Using the center stake make sure your 

pool is completely in true round by measuring 
from the center of the stake to inside of pool 
wall

 in all directions, making sure these 

measurements are equal. 

Remove center stake from pool area after 

measurements and adjustments, if necessary, 
are made. 

PROTECT YOUR LINER 

from top to bottom of wall.  If the filter inlet and outlet 
are not used, cover over the pre-scored areas on the 
inside of the pool wall with 1 layer of tape. 

I f   y o u r   P o o l   Wa l l   h a s   t h e  
Recessed Posi-Lock System an 
additional layer of tape should 
be added to the inside part of the 
extended end of the wall. 

INSIDE OF 

Cloth tape or duct tape is 

POOL VIEW 

available through your local 
pool dealer or hardware 
store. 

12 

Summary of Contents for 7" XL


























Reviews: