47
E
N
G
L
IS
H
Directions for the user
To change the language in the control panel:
- Switch from the base display by pressing the
Menu
button
(Menu) to advance to the
Main menu
- When the main menu opens, the marker is placed at
Language
- Press the
Select
button
- Select the language with the
buttons and press the
Set
button
- You can return to the base display if you wait a moment or if you
press the
Return
button enough times
To set the time and the weekday:
The display shows the time and the weekday. If required, this
function can be disabled in the Installation and Service menu.
- For example, press the right-hand button once to activate the
control panel.
- Immediately press the right-hand
Menu
button once more to
return to the
Main Menu
- Use the
buttons to change to the Clock image
- Press in the right-hand button Select to switch to the
Clock
menu
- Use the
buttons to change to the Clock image
- Press in the right-hand Select button to switch to the
Time
menu
- Set the hours with the
buttons
- Switch to setting of minutes with the
-button- Set minutes
with the
buttons
- Confirm the time by pressing the right-hand button
Set
- The display returns to show
Clock
- Use the
buttons in order to switch to
Weekday
and press
Select
- Use the + and – buttons to advance to the appropriate weekday
- Confirm the weekday by pressing the
Set button
- You can return to the
Base display
if you wait a moment or if
you press the
Return
button enough times
To set reheating:
The reheating function is factory-preset for the discharge of air at
a temperature of 17 °C into the room.
N.B.! Reheating cannot be used simultaneously with
cooling of the air in the summertime. The Summer night
Cooling function must be shut-off before reheating can
be enabled.
- Switch from the base display by pressing the
Menu button
to
advance to the
Main menu
- Select
Reheat
and press
Select
- In the
Heating equipment menu,
select the option
On
- Confirm and return to the
Main menu
- Switch to the
Main menu
point
Temperature
and press
Select
- The
temperature
menu allows you to change the
Supply air
temperature [13–20 °C]
Summer night cooling:
The Summer night cooling can be used if the temperature of the
supply air exceeds the temperature of the outside air. The function
can only be used if the temperature is higher than 13 °C. The
lower set value of the temperature of the indoor air, the earlier
the function starts. The airing effect can be changed with the fan
speeds belonging to the function.
N.B.! Cooling of the air in the summertime cannot be used
simultaneously with the reheating. The Summer night
cooling function must be shut-off before the reheating can
be enabled.
- Go from the base display by pressing the
Menu button
to
advance to the
Main menu
- Switch to
Summer night cooling
and press
Select
- In the
Summer night cooling menu
select the alternative
On
- Switch to
Start temperature
- Specify at
Start temperature
the desired indoor temperature.
This enables the function. The factory setting is 21 °C.
- In the
Summer night cooling image,
switch to
Fan speed
and press
Select
- In the
Fan speed menu
you can change the fan speeds for the
Summer night cooling. [No change/Away/At Home/ Boost/Cool-
ing]. Because it is factory preset, the fan speed is not changed,
but the value set by the user applies.
Base display:
The display shows the fan speed selected for the ventilation unit
- In the Away/At Home/Boost settings = Base display 1
- Stepless = Base display 2
- Switch from the base display by pressing the
Menu button
to
advance to the
Main menu
- Switch to
Base display
and press
Select
- Enable either
Base display 1 or Base display 2
To switch off the unit:
When the ventilation unit is switched off from the control panel, the
fans stop and the air heater is switched off. The circuit card is how-
ever still energised and the settings are preserved in the memory.
- Switch from the base display by pressing the
Menu button
to
advance to the
Main menu
- Switch to
Shut-off
and press
Select
- The display will show
Shut-off?
and you can confirm by press-
ing the right-hand button.
Fireplace switch function:
The quick selection button of the fireplace function is available as
standard on the control panel. The fireplace function temporarily
generates positive pressure in the home, making it easier to light
a fire in the fireplace. The fireplace function lasts 10 minutes. In
homes
without fireplace
the function can be disabled from the
control panel as described below.
- Switch from the base display by pressing the
Menu button
to
advance to the
Main menu
- Switch to
Fireplace function
and press
Select
- In the
Fireplace function
menu, set
Off
Summary of Contents for ILTO X100 Premium
Page 63: ......
