swaploader SL-400 Parts And Operation Manual Download Page 75 | Manualshive

Page: 75 / 136

swaploader SL-400 Parts And Operation Manual Download Page 75

10/05/09

REAR LIGHT BAR ASSEMBLY

(51H68)

ADDITIONAL NOTES:

Prior to any welding, consult the truck
manufacture for any special precautions
that may need to be taken. Typically the
batteries must be disconnected and the
ground lead from the welder should be
as close to the part being welded to
avoid the possibility of arcing across
bearings, gears, etc.

8.

Mount junction box on the back left side of center plate (See Fig. 2), using the fasteners

provided (See Fig. 3).

9.

Route all wire harnesses into the junction box. Wire harnesses must enter the junction box

through a compression fitting (Based on the size of the wire harness, choose a
compression fitting with an appropriately sized grommet). Make wiring connections in
junction box with wire harness from truck cab as indicated on wiring diagram (See Fig.4).

FIG. 3

1800 NE Broadway Avenue, Des Moines, Iowa, U.S.A. 50313-2644

Phone: (515) 266-3042

•

Fax: (515) 313-4426

•

Toll Free: (888) 767-8000

E-Mail: [email protected]

•

Web Site: www.swaploader.com

«
...
73
74
75
76
77
...
»

Summary of Contents for SL-400









































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands