background image

2

2

2

FCC Verifi cation:
NOTE: 

This equipment has been tested and found to comply with the limits for 

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to cor-
rect the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna
· Increase the separation between the equipment and the receiver
· Connect the equipment into an outlet on a circuit different from that to which 
the receiver is connected
· Consult the dealer or an experienced radio/TV technician for help

IMPORTANT NOTE:

 

Prohibition against eavesdropping

Except for the operations of law enforcement offi cers conducted under lawful 
authority, no person shall use, either directly or indirectly, a device operated pursu-
ant to the provisions of this Part for the purpose of overhearing or recording the 
private conversations of others unless such use is authorized by all of the parties 
engaging in the conversation.

WARNING: 

Modifi cations not approved by the party responsible for compliance 

could void user’s authority to operate the equipment.

IMPORTANT SAFETY INSTRUCTIONS: 

· Make sure product is fi xed correctly and stable if fastened in place
· Do not operate if wires and terminals are exposed

2

FOR BEST RESULTS:

This is a semi-professional 360

º PTZ dome camera, conforming to PELCO P/D stand-

ards. To obtain the best image quality, please use a high quality cable, particularly if 
the cables required length exceeds 100ft/35m. For the highest video quality, use a 
cable with a solid copper inner conductor and shielded with copper braid.

Before You Begin

19

Video

Image 

Sensor 

  1/3” 

CCD

Video Quality 

 

 

600 TV Lines

Number of Effective Pixels 

 

NTSC:  

768 x 494

    PAL: 

 

752 

582

Minimum Illumination 

 

0.01 Lux

White 

Balance 

  Automatic

Signal / Noise Ratio   

 

> 50dB

Electronic Shutter 

 

 

NTSC: 1/60 – 1/100, 000

    PAL: 

1/50 

– 

1/100, 

000

Gain 

Control 

  Automatic

Backlight Compensation 

 

Yes

Lens 

   Vari-focal 

4-9mm

Viewing Angle 

 

 

30 – 60 degrees

Zoom 

   3x 

Optical

PTZ Features

Dome Type 

 

 

4” PTZ Dome

Baud 

Rate 

   1200/2400/4800/9600 

bps

Pan 

Rotation 

  Continuous 

360º

Tilt Rotation 

 

 

0º ~ 90º

Preset Points 

 

 

Up to 32

Preset Panning Speed 

 

35º/sec

Preset Panning Accuracy 

 

+ / - 3º

Programmable Pattern 

 

Up to 16 preset points

PTZ Controller

Interface 

Type 

  RS485

Protocol 

   Full 

Function 

Pelco 

P/D

Address 

   0 

– 

255

Display 

Type 

  4 

LED

Remote 

Control 

  Included

Battery Type 

 

 

2 x AAA

General

Operating 

Power 

  DC 

12V

Operating Temperature 

 

23ºF ~ 140ºF / -5ºC ~ 60ºC

Body 

Construction 

  ABS 

Plastic

Dimensions – Camera 

 

5.9” x 3.1” x 4.9” (150mm x 125mm x 125mm)

Dimensions – Stand   

 

4.5” x 3.1” x 5.3” (80mm x 72mm x 28mm)

Weight – Camera 

 

 

500g / 1.1lbs

Weight – Camera & Stand 

 

700g / 1.5lbs

Weight – Controller   

 

85g / 3oz

Technical Specifications

Summary of Contents for PRO-690











Reviews: