background image

3

Introduction

Safety Information

Congratulations on your purchase of this Swann 1080P PTZ IP Camera! It is an ideal solution for 

monitoring a large area - a combination of a high quality CMOS image sensor mounted in a contained 

dome with the option to fully pan 360 degrees. Nothing will be out of sight for long. 

The following instructions are intended to ensure that you use the camera correctly and to avoid danger 

or property loss.

Warning:

• 

With the use of the camera, you must follow strict compliance with the safety regulations in 

accordance to your country and region.

• 

Only use the supplied power adapter. The standard of the power adapter is AC24V/3A.

• 

Do not connect multiple devices to a single power adapter, as an overloaded adapter may cause 

a fire hazard.

• 

When installing the camera, ensure it is firmly secured and fastened in place.

• 

If smoke, odours or noise come from the device, turn off the power at once and disconnect the 

power cable and then contact Swann Technical Support. Continued use in such a condition may 

cause fire or electrical shock.

• 

If the product fails to operate properly, do not attempt to disassemble the camera yourself. (We 

shall not assume any responsibility for problems caused by unauthorized repair or maintenance).

Caution:

• 

Do not drop the dome or subject it to physical shock. Avoid installing the dome in a location subject 

to excessive vibration or high electromagnetism radiation.

• 

Do not install the dome in extremely hot, cold (the operating temperature should be -30°C ~ 

+65°C), dusty or damp locations. Doing so may cause fire or electrical shock.

• 

Avoid exposing the dome cover to rain and moisture.

• 

Do not expose the dome to direct sun light, low ventilation or heat source such as heater or 

radiator. Doing so may cause fire.

• 

Use the supplied glove when removing the dome cover. Avoid direct contact with the dome cover 

because the acidic sweat of the fingers may erode the surface coating of the dome cover.

• 

Use a soft and dry cloth when cleaning inside and outside surfaces of the dome cover. Do not use 

alkaline detergents.

Summary of Contents for 1080P PTZ IP Camera











Reviews: