MIC
LINE IN
0
5
10
REVERB
-10
0
+10
TREBLE
-10
0
+10
BASS
10
9
8
7
6
5
4
3
2
1
0
GAIN
CHANNEL 1
MIC
LINE IN
0
5
10
REVERB
-10
0
+10
TREBLE
-10
0
+10
BASS
10
9
8
7
6
5
4
3
2
1
0
GAIN
CHANNEL 2
MIC
LINE IN
0
5
10
REVERB
-10
0
+10
TREBLE
-10
0
+10
BASS
10
9
8
7
6
5
4
3
2
1
0
GAIN
CHANNEL 3
0
5
10
REVERB
-10
0
+10
TREBLE
-10
0
+10
BASS
10
9
8
7
6
5
4
3
2
1
0
GAIN
CHANNEL 4
0
5
10
REVERB
-10
0
+10
TREBLE
-10
0
+10
BASS
10
9
8
7
6
5
4
3
2
1
0
GAIN
CHANNEL 5
+12
+6
0
-6
-12
+12
+6
0
-6
-12
LOW LOW/MID MID HIGH/MID HIGH
PEAK
POWER
UP
DOWN
DIGITAL EFFECT PROCESSOR SYSTEM
4-Room3
5-Plate1
6-Plate2
7-Plate3
0-Hall1 1-Hall2 2-Room1 3-Room2
8-Chorus
9-Flange
A-Delay1
B-Delay2
C-Chorus/Room1
D-Chorus/Room2
E-Vocal Cancel
F-Rotary Speaker
CH.1
CH.2
CH.3
CH.4
MIC IN
STEREO
LEFT/MONO
RIGHT
CH.5
CD
IN
TAPE
OUT
L
R
MODE
MONO
STEREO
10
9
8
7
6
5
4
3
2
1
0
MASTER
L
R
1 5 0 WATTS POWERED MIXER
5.Function introduction
：
A. Channel1-3: mono Combo (XLR and 1/4
″
double service phone Jack) input
plug hole
1. Combo input plug hole
2. Reverberation control knob
3. Treble and bass volume control
4. Channel gain attenuators
B. Channel4. Phone balanced input (XLR) and R, L channel stereo input track
C. channel5. CD input with RCA socket and TAPE output
D. diagrammatic equalizer
E. digital effect processing panel / digital delay
F. main volume attenuator
G. stereo/mono channel switch
(2) Take out the speaker stands, adjust to the needed height, and make sure
the ground is flat enough to connect firmly
(3) Mount the speak cabinet on the stands before the audience .keep the spe-
aker cabinet away from microphone in order to avoid echo
(4) Connect the speaker cabinet to the mixer in the plastic jacket and ma ke
sure left channel in speaker cabinet is connected to the left channel in the
mixer, the same as the right channel.
CH.5
CD
IN
TAPE
OUT
L
R
(1) Choose dynamic microphone. Because of this PA system without phantom
power, it can not work with any microphone needed phantom power, such
as dynamic microphone and so on.
(2) Choose suitable microphone or you choose
dynamic microphone by yourselves.
Choose suitable cables with XLR connector
to connect microphone to any channel.
·
Microphone installation
(1) Connect CD/TAPE player to channel 5 with RCA connector
(2) Connect L and R to corresponding mixer port
(3) Adjust tone. Gains and reverberation by CD channel
·
CD player installation
3
9 meters speaker link cables 2 PCS
Speaker stands 2 PCS
Dynamic Microphone 1 PCS
6 meters microphone link cables 1 PCS
Fuse
Φ
5x20mm T 3AL 2 PCS
4. Accessory:
6. Installation introduction
·
Speaker cabinet installation introduction
(1) Take out the speaker cabinet and then connect them
MIC
LINE IN
CH.3
2
