background image

 

 It should be taken and put slowly; 

 In order to watch the condition of system, power box should be put in the place 

where is easy to watch; 

 In order to connect other accessories (solar panels, battery, DC lamps, TV set and 

so on), power box should be put in a moderate position. 

 Be more careful when install and transport the batteries. 

 If the storage period of battery exceed 6 months, it should be charging maintained. 

The storing place should be dry, clean and ventilate. 

6.2.3 Connect solar to power box

 

 

Before connecting the cable, please confirm that the load switch of power box is 

located in “OFF/0N” position.

It is strictly not allowed to connect positive and navigate 

of solar module in reverse; 

After connection, cable should be put in the place where is not easy to touch. 

 

Please confirm the distance from solar bracket to power box. The length of cable is 

15 meters. We use 2.5mm

2

×15m cable to connect solar module to power box. First 

open the junction box at the back of solar module, and then insert it   in the hole. 

After connected two cables, screw down the waterproof connection and cover the 

junction box. 

Attention: 

 While connecting, cover the solar module of put it in a poor light; 

 There may be spark when connecting, users must be careful! 

 Cable can be an aerial cable. If it is put under the ground, it should be put into a 

protecting cannula. 

 

6.2.4 Connect load to the power box

 

At the faceplate of power box, there are three 12VDC lamps or DC TV 
output port and one 9VDC radiogram output port. Connect DC lamps or DC 
TV and radiogram to the corresponding socket. The length of cable is 6 
meters, please consider best putting position. 

After the above steps, the installation of SHS-50 has been finished. 

7. Operating method of FS-SHS050

 

SHS-50 is the system which can be used easily. Power box is the core 
of the system. Because that charge controller, battery, switch and all the 
ports are installed in the box. 

7.1 Charge for battery

 

After  confirming  the  veracity  of  the  system  installation,  connect  the  solar cable to 
the relevant socket  on the power box, then it can charge for battery. At this time, 
the  green LED  indicator  of  charge  controller  is  lightening.  This  cable  can be 
connected with power box all the time. 

Summary of Contents for SHS050W

















Reviews: