SVERO Smart Hoist 22 Manual Download Page 9 | Manualshive

Page: 9 / 16

background image

Svero Lifting AB | Momarken 19, 556 50 Jönköping, Sweden

T:

+46 (0) 36 31 65 70

9

Pic. 12 Center the Holder under the beam

6.

Fasten the stop screw for the side plate with cover (pos. 2 on Fig. 2) lightly, in the
same way as in Pic. 10 above.

7.

Check the centering of the Holder and the clearance between the beam flange and
the wheel flange. Tighten the stop screws. The top of the screws should now be
level with the surface of the side plate (Pic. 13). The stop screws are prepared
with a thread-locking fluid

so that they can’t lo

osen because of vibrations caused

when moving the Smart Hoist along the beam. You should be able to screw the
stop screws in and out a number of times without loss of performance, but always
make sure that the thread-looking fluid is working. Otherwise add looking fluid.

«
...
7
8
9
10
11
...
»

Summary of Contents for Smart Hoist 22

















Reviews:

No comments

Related manuals for Smart Hoist 22

Brand: Pacific Hoists Pages: 18

Brand: Guldmann Pages: 109

Brand: J. D. NEUHAUS Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands