background image

1-5

INSPECTION BEFORE RIDING

Review the instructions in the
“INSPECTION BEFORE RIDING”
section of this manual. Perform an
entire pre-ride inspection before
you head out on the road. Spend-
ing a few minutes preparing your
machine for a ride can help pre-
vent accidents due to mechanical
failure or costly, inconvenient
breakdowns far from home.

ACCESSORIES AND LOADING

The accessories you use with
your motorcycle and the manner
in which you load your gear onto
the bike might create hazards.
Aerodynamics, handling, balance,
and cornering clearance can suf-
fer, and the suspension and tires
can be overloaded. Read the
“ACCESSORY USE AND
MOTORCYCLE LOADING” sec-
tion.

CARRYING A PASSENGER

Carrying a passenger, when done
correctly, is a great way to share
the joy of motorcycling. You will
have to alter your riding style
somewhat since the extra weight
of a passenger will affect handling
and braking. You may also need
to adjust tire pressures and sus-
pension; please refer to the Tire
Pressure and Loading section
and the Suspension section for
more details.

A passenger needs the same pro-
tection that you do, including a
helmet and proper clothing. The
passenger should not wear long
shoe laces or loose pants that
could get caught in the wheel or
the chain. Passengers must be
tall enough that their feet reach
the footrests.

Summary of Contents for V Storm
































































































































Reviews: